Skip to Content

Can a direct to stud tub surround over drywall?

Yes, it is possible to install a direct to stud tub surround over drywall, however there are a few things that should be taken into consideration before attempting this. First, you will need to make sure that the drywall is made of the appropriate material for wet areas and is installed properly.

Drywall should be at least 1/2 inch thick and made from gypsum boards that are specifically rated for wet areas. It should also be reinforced with greenboard, sometimes referred to as tiling drywall, before installing the tub surround.

Additionally, the studs behind the drywall should be plumb and level if the installation is going to be successful. If the studs are made from wood or other material, they will need to be replaced with metal or plastic studs with adequate support to ensure that the tub surround is well supported.

Finally, you should always follow the manufacturer’s installation instructions precisely to ensure that your new surround is properly and safely installed.

Do you need cement board behind tub surround?

Yes, it is generally recommended to use cement board behind a tub surround for multiple reasons. Cement board provides a waterproof, durable surface that prevents moisture from seeping into the wall and causing mold and mildew to form.

It is also stronger than drywall, providing a sturdy surface for the tub surround to be attached to. In some cases, local or state codes may require the installation of cement board for safety reasons, such as a fire safety rating or an increased weight limit.

Additionally, installing cement board incorporates an extra layer of insulation that helps keep the wall warm and improve the soundproofing capabilities of the wall. Adding cement board is an important part of finishing a bathroom renovation and should not be skipped if possible.

Can you install shower surround to studs?

Yes, it is possible to install shower surround to studs. Before you begin, it is important to make sure that the walls of the shower surround are suitable for this type of installation. If the walls of the surround are made of a material that is not designed to be attached to studs, then it is not possible to install the surround using studs.

Once you have determined that the walls are suitable for this type of installation, the next step is to make sure that the studs are in the right place. This can be done by measuring the distance between them, as well as the height of the walls.

The walls need to be even and straight so that the shower surround can be installed properly. Once the measurements are taken, you can mark the studs on the wall to make sure that they are in the right place.

Next, you will need to apply a silicone adhesive to the back of the shower surround. This will help to hold the surround in place while it is being attached to the studs. Once the adhesive has been applied, you can then attach the shower surround to the studs using screws or nails.

Make sure that the screws are long enough to hold the surround securely, as well as being driven into the studs firmly.

Finally, the last step is to caulk the edges of the shower surround to ensure that it is watertight. This will help to prevent any water from getting behind the surround and into the walls, causing damage.

Once this is done, your shower surround should be securely in place, and you can enjoy using it in your bathroom.

What kind of drywall do you use behind a tub surround?

When choosing drywall to use behind a tub surround, the most important factor to consider is the type of environment the drywall will be exposed to. Generally, for most tub surrounds, water-resistant drywall is the best choice.

This type of drywall, often referred to as “green board” or “moisture-resistant drywall,” is made with a green paper face and is treated with a wax compound to help resist water. It’s ideal for bathrooms, laundry rooms, and even kitchens where there’s an increased chance of moisture coming into contact with the drywall.

Regular drywall, on the other hand, is not recommended for these rooms as the moisture can cause it to get damaged or even rot, leading to further complications. A third option is ‘mold-resistant drywall’, which has a core made of gypsum and silver ions that act as a barrier to protect the drywall from fungus and bacterial growth.

Although this drywall doesn’t repel moisture it is resistant to any mold or mildew that may form. Ultimately, the right type of drywall to use behind a tub surround depends on personal preference, the type of bathroom environment, and the budget of the homeowner.

How do you waterproof drywall around a bathtub?

Waterproofing drywall around a bathtub is an important step when renovating a bathroom to prevent water damage. To do this, you’ll need to apply a bead of waterproofing sealant, such as caulk, along the perimeter of the bathtub where it meets the wall1.

Then, you don’t need to do anything special to the drywall itself; install it as normal, being sure to firmly press the joint tape along each seam2. If desired, you can apply a waterproofing paint or coating over the drywall3.

Finally, apply a large piece of waterproofing membrane to the walls and run it up along the tub4. This membrane is designed to keep water out, so it’s important to make sure it’s properly sealed5. All of these steps should help ensure that your drywall remains dry, and your bathroom renovation lasts for many years to come.

How do you prep a wall for a tub surround?

Preparing a wall for a tub surround requires precise measuring and measurements. Depending on the type of surround, you may need to make some modifications to the wall first.

First, measure the surrounding area to make sure the tub will fit the space. Remove any drywall using a drywall knife or drywall saw and remove any drywall. If the area is not framed, use a framing nailer to frame it to the wall.

Secure the framing with 3-inch construction screws. Make sure the frame is level.

If you’re using a tub surround kit, use the instructions provided to make sure everything is lined up properly. If you’re not, follow the instructions provided by the manufacturer of your chosen surround.

Next, prep the wall. The simplest option is to use cement board or fiberglass tile backer. Measure and cut the backer to fit over the framing. Start at the bottom of the wall and work your way up applying thin-set mortar as suggested by the manufacturer instructions of your chosen backer.

Once you’ve applied the backer, nail or screw it into the framing.

Finish prepping the wall by applying water-resistant mesh tape to the seams. This will help prevent water from seeping through. Apply a thin layer of thin-set mortar to the entire wall and smooth it out.

Let it dry for a couple of hours.

Finally, you’re ready to install the tub surround. Line up the surround with the edges of the wall and press it into place. Follow the directions provided by the manufacturer for further installation instructions.

Follow these steps to properly prep a wall for a tub surround. As long as you accurately measure the area, you should be able to successfully install your surround.

Can I glue tub surround to plywood?

Yes, you can glue tub surround to plywood. The best way to do so is to use a quality construction adhesive specifically designed for bonding wall materials together such as tub surround and plywood. Make sure the surfaces are clean, dry and free of debris before applying the adhesive.

You may need to use a straight edge or level to make sure the surfaces are even before applying the adhesive. The adhesive should be applied evenly with an caulking gun and allowed to dry as directed on the manufacturer’s instructions before attempting to bond the surfaces.

Once the adhesive has dried and the surfaces connected, it is important to allow the bond to cure for the amount of time listed on the product packaging before using or applying any pressure or weight to the area.

Do you screw a tub to studs?

Yes, it is important to secure a tub to studs when installing it. This will help ensure the tub is securely and safely installed to the wall. Depending on the type of tub you are installing, you may need to use metal straps or mounting brackets to secure the tub to the studs in the wall.

If the tub isn’t secured properly, it can easily become loose or even fall off the wall, putting those in the tub or bathroom at risk of serious injury. If possible, it is best to have a professional help with the installation to ensure maximum security.

Can you use regular drywall around a shower?

Yes, you can use regular drywall around a shower. However, when doing so, it’s important to keep in mind that regular drywall does not have the necessary waterproofing properties needed to protect it from moisture damage.

Because of this, it must be treated with special moisture-resistant sealants and coatings to help protect it from water damage. Additionally, it’s important to ensure that all the seams between drywall panels are properly sealed to prevent water from seeping through.

When doing a shower project, it’s also recommended to use moisture-resistant drywall boards or coated gypsum boards in place of regular drywall to help protect against water damage. It’s also important to properly waterproof the floor and corners of the shower to prevent water around the drywall area.

What material goes behind shower walls?

When constructing a shower, it is important to install the appropriate materials behind the walls to help protect the bathroom from water damage and create a waterproof, long-lasting space. The type of material used behind the shower walls should depend on the size and configuration of the space, as well as the budget and desired look of the final product.

For smaller shower spaces, cement boards such as Durock cement board or HardieBacker cement board are often used. Cement boards are a universal material that can be used behind almost any type of tile, and they are waterproof, mildew resistant, and durable.

For more light-weight projects, a moisture-resistant composite material such as WonderBoard Lite can be used.

For larger shower spaces, think about incorporating a waterproof membrane behind the shower walls. This barrier helps provide an extra layer of protection against leaks. Waterproof membranes are made out of flexible materials, such as PVC and PEVA, and are installed between the studs and under the tile.

In addition to these materials, be sure to install vapour barriers to help prevent moisture transfer between the walls and the shower. Vapour barriers, such as polyethylene plastic sheets or kraft-faced insulation, are important to prevent mould growth and water damage to the walls.

When used along with the appropriate sealants, the materials discussed above should be enough to build a safe, waterproof shower enclosure.

How do you install a direct to stud shower enclosure?

Installing a direct to stud shower enclosure requires some basic carpentry and plumbing knowledge and a few specialized tools. Before starting your installation project, be sure to check your local building codes and obtain any necessary permits.

Then follow these steps:

1. Shut off the main water supply and remove any existing fixtures including shower valves, spouts, and diverter handles.

2. Use a studfinder to locate existing studs in the wall, marking them with small dots on the wall surface. Once you have determined stud placement, use a level to draw level lines across the studs to ensure that your framing will be perfectly square.

3. Cut a top, bottom, and side frame out of 2×6 lumber to fit within the stud lines. Secure the frame into the studs with wood screws.

4. Add additional 2×6 pieces to the original frame, forming a box that is open at one end.

5. Cover the back side of the frame with a vinyl moisture barrier. Overlap the bottom layer over the back of the frame by an inch and fold over the top and sides like wrapping a present.

6. Cut and fit a piece of 1/4” plywood to the inner surface of the frame. Secure it with 16-gauge nails or screws every 8-10 inches.

7. Now apply wallboard or hardie board to the exterior side of the frame using wallboard screws or adhesive.

8. Install 2×4 blocking to the stud area and then install cement board as the shower base.

9. Secure the shower enclosure to the wall with appropriate fasteners and silicone caulk.

10. Install drain and water lines according to the manufacturer’s instructions.

11. Connect the faucet, shower head, spout, and diverter handle to the water supply lines.

12. Install the shower doors with the necessary hardware and seal all openings with the silicone caulk.

13. Test for leaks before using the shower.

What do you put behind a shower surround?

When installing a shower surround, there are a few easy steps that should be taken to properly install it and ensure it lasts. First, the area should be measured and marked out before the project begins, ensuring the surround will fit the space and the tile is placed correctly against the wall.

Second, the walls should be prepped by priming and cleaning them so the adhesive will stick. Third, the adhesive should be placed along the wall and the surround should be pressed to the wall, ensuring that all connections are secure.

Once the initial connection is made, anchors should then be placed in the wall behind the surround, which will provide additional stability. Lastly, grout should be added around the edge of the surround as an extra line of defense against water infiltration and as an aesthetic touch.

Can you put shower panels straight onto plasterboard?

Shower panels can be attached to plasterboard walls with the right preparation process, although this can be difficult and time consuming as the plasterboard should be water-proofed and given extra protection against any moisture to ensure the longevity of the panels.

It is recommended you use battens and fixings to securely fit the shower panels to the wall and reinforce the plasterboard. Depending on the weight of the panelling, it might also be necessary to reinforce the plasterboard or use a backing board to help provide a solid base.

If the wall will come into contact with a lot of moisture, it could be preferable to use tiles or wet wall lining instead to avoid any damage. Make sure to seek advice from a professional before installing shower panels to plasterboard walls.

What can you put between shower and wall?

The most important item that should be installed is a shower liner or curtain. This will prevent water from splashing onto the walls and floor. Other items that can go in between a shower and wall include towels bars and shelves.

Towel bars will be helpful in keeping towels and other items off the floor and out of the shower, while shelves can be used to store essential toiletries. Additionally, you could add a freestanding shower caddy for organizing shower essentials.

If you prefer a more decorative touch, you could also add a mosaic tile strip to make your bathroom look more personalized and stylish.

Is drywall OK above shower?

Yes, drywall is generally considered safe to use for walls and ceilings in any bathroom, including above showers and bathtubs. However, to ensure that the drywall is adequately protected from moisture, it is important to use waterproofing materials and techniques, such as a vapor barrier.

A vapor barrier is a special type of plastic sheeting or coating that prevents moisture from getting through to the drywall. It should be installed directly on the framing of the wall, before the drywall is attached.

After the vapor barrier is in place, a specially designed drywall designed for bathrooms should be used in order to provide additional protection against water. In addition, standard drywall should be covered with a water-resistant paint or sealant in order to protect it further.