Skip to Content

Can a toilet be away from a wall?

Yes, a toilet can be away from a wall. Including corner toilets, wall-mounted toilets, upflush toilets, and macerating toilets. Corner toilets are round or elongated toilets that are designed to fit into a corner of the bathroom and can be located away from walls.

Wall-mounted toilets also do not require wall placement, and instead are attached directly to the floor and do not touch the wall. Upflush toilets are also designed to be away from a wall and use a pump to flush the waste up through a drainpipe in the wall or floor.

Lastly, macerating toilets can be installed under the stairs, in corners, and other tight spaces that are away from the wall.

How far away should a toilet be from the wall?

When installing a toilet, it is important to leave the proper amount of space between the back of the toilet and the wall. To ensure that you have enough space to install it, it is recommended that you leave an 8-inch gap between the back of the toilet and the wall.

This gap should be measured from the back side of the bowl, and giving yourself 8 inches will give you enough room to install the toilet and do any necessary maintenance. Additionally, leaving this gap between the toilet and the wall also helps to reduce noise from the toilet when it refills or flushes.

Does a toilet have to be against a wall?

No, a toilet does not have to be against a wall. For most bathrooms, having the toilet against a wall is the best option, as it provides an additional stability and makes the installation easier. It also helps to keep the room tidy by controlling the direction of pipe and water running.

However, other arrangements are possible depending on the type of toilet, premise size, and budget. If there is ample space, a freestanding toilet can be placed in the middle of the room, or a corner toilet can be installed.

In some cases, it might be advantageous to offset the drainage point away from the wall to reduce noise. Additionally, if the existing plumbing system does not support the toilet installation to a wall, the toilet can be installed on the floor.

How do you fix a toilet that is too far from the wall?

Fixing a toilet that is too far away from the wall can be a tricky job, but it is possible. First, you will need to turn off the water to the toilet and flush the tank until it has emptied completely.

Next, you will need to locate the footings of the toilet and remove them by prying them off with a flathead screwdriver. Then, you need to lift up the toilet, carefully move it to the desired position, and screw the footings back in place.

Once that is done, you will need to turn the water back on and flush the toilet to make sure everything is working properly. If you experience any leaks, you may need to apply a sealant or adjust the footings slightly.

Finally, inspect the toilet and make sure it is flush with the wall.

Are all toilets 12 inches from wall?

No, not all toilets are 12 inches from the wall. The general standard is that toilets should be 12 inches from the wall, but this is only a guideline and not a strict requirement. Depending on the specific style of toilet, as well as the particular installation, the exact distance from the wall may vary.

For instance, some low-flow toilets may require more space between the wall and the back of the toilet, while other kinds of toilets may be able to fit against the wall closer than 12 inches. Additionally, the space between the wall and the back of the toilet may be affected by the size and shape of the wall and the type of toilet being installed.

Ultimately, it is up to the individual installer to measure how far the toilet should be placed from the wall, as this can vary from situation to situation.

Can you fit a toilet anywhere?

No, you cannot fit a toilet anywhere. Proper installation of a toilet requires a drainage system and access to a water supply. The toilet must be placed above the drainage pipe, and it should also be within arm’s reach of the water supply line.

You must also ensure that the toilet will fit in the allotted space, as well as being level on the ground and supported by a sturdy base. A note of caution: when planning the installation of a toilet, always check with local building regulations, as some municipalities have specific requirements for toilet installation.

Finally, it is always best practice to have a professional plumber perform the installation of a toilet to ensure the correct installation and that it meets code.

Do you need planning permission to move a toilet?

Yes, in most cases you will need planning permission to move a toilet. Depending on the size and scope of the project, this may require a building permit as well. Generally speaking, any structural changes will require planning permission, and moving a toilet would fall under this category.

If the toilet is being moved to a new location and any plumbing or electrical work needs to be done, you would need the relevant permits for that work as well. It is best to contact your local municipality or planning authority to confirm the regulations and to provide any necessary paperwork.

Is it a big deal to move a toilet location?

Moving a toilet location is an involved renovation. It’s not something that can be done quickly or easily, so it is a fairly big deal. You may need to tear out bathroom walls or floors and rearrange plumbing in order to move the toilet.

Depending on the space constraints, this could require closing off sections of the bathroom or even renovating other areas of the bathroom to accommodate the new toilet location. It is not just a matter of simply uninstalling the toilet and reinstalling it somewhere else.

The toilet needs to be securely fastened to the floor, which may require extra bracing or wall supports. You may also need to move other fixtures, like the sink and bathtub, to make room for the toilet.

Furthermore, the plumbing lines to the toilet will have to be reconfigured or extended in order for the toilet to work properly. Because of all the work involved, it is indeed a big deal to move a toilet location.

How far can a toilet be moved?

The distance a toilet can be moved is generally dependent on the plumbing system of each individual house. In most cases, a toilet can be moved up to a few feet in either direction, as long as it remains within the same area as the existing drainpipe and water supply lines.

It is important to consider the layout of the existing plumbing system before attempting to move a toilet. If the existing drain and water connections are not long enough to reach the desired location, they will need to be lengthened or replaced, which is typically a job best left to a professional.

Not doing so may result in leaks, improper plumbing connections, and costly repairs down the line. Additionally, if the bathroom is being renovated, updating the toilet flange should be taken into consideration as it will allow for an easier install of the new toilet.

When in doubt, it is best to contact a professional for assistance with plumbing and toilet installation to ensure the job is done correctly.

How much does it cost to move a toilet to a different wall?

The cost to move a toilet to a different wall can vary greatly depending on a number of factors, such as the amount of plumbing work needed, the amount of wall repair required, and the complexity of the job.

Generally, you can expect to spend between $900 and $1,500 for a simple job. However, if more plumbing work is needed, or if more wall repair is needed, the costs can increase significantly. In total, it could cost anywhere from a few hundred dollars to a few thousand to move a toilet to a different wall.

It is a good idea to consult with a plumber to get a better idea of what to expect in terms of costs.

How hard is it to reroute a toilet?

Rerouting a toilet can be a difficult job, depending on the specific circumstances surrounding the project. In some cases, the entire bathroom may need to be remodeled in order to create a safe, functional and aesthetically pleasing layout that makes the most of the space.

In other cases, the current layout of the plumbing can be utilized to redirect the position of a toilet.

The most difficult part of the job will typically be the removal of the existing toilet and repositioning of the supply and drain lines. When working with a standard residential or commercial setup, the wastewater line will usually consist of a stubbed-out connection to existing plumbing fixtures, such as sinks, tubs and washing machines.

As such, there may only be a very small gap to snake the drain pipes through in order to properly redirect the pipes. The supply line may also have to be extended further in order to reach the new location of the toilet.

This can involve the removal of drywall, fixtures and other items, making it more difficult to get the job done.

In addition, the process may require the use of specialty tools and materials, such as a snake, pipe wrench, hacksaw, PVC or ABS pipe and plumbing cement. It will also require knowledge of local plumbing codes and regular maintenance requirements in order to ensure a safe and functioning bathroom.

When performed correctly, the new layout should be both aesthetically pleasing and properly designed in order to maximize water efficiency.

Overall, rerouting a toilet can be a difficult job requiring time, expertise and knowledge. With proper tools, materials and a good plan, the process can be completed with minimal disruption to the home or business.

How far can a toilet drain drop straight down?

The exact distance a toilet drain can drop straight down depends on the set up of the individual plumbing system. Most toilets have a drop of approximately 2 feet (0. 6 m), but it can vary. Generally, it is best practice to keep the distance as short as possible, as the volume of water in a toilet’s outgoing flushing jet follows the laws of physics, meaning that it has to lose pressure and velocity over a long vertical drop.

A longer vertical drop can result in slower flushing and an increased possibility of a clog. It is best to keep any vertical drop to less than 6 feet (1. 8 m). If the drop in plumbing must be longer, the system should use a sewer venting system with a wye fitting to prevent water pressures from building up dangerously.

How high do you stub out for water lines on toilet?

The standard height for water lines for a toilet is 12 inches, measured from the finished floor to the bottom of the closet elbow (the curved pipe that comes out of the wall). This height allows a standard toilet bowl to be comfortably used by most users and provides sufficient clearance to position a wax ring, install the bowl and finish flushing the toilet.

However, this height might need to be adjusted to fit the needs of users, including those with special access requirements, in which case the water lines should be set higher or lower depending on the situation.

For example, people with physical disabilities will often require a higher stub-out height to make it easier to transfer in and out of the bathroom.

Should toilet pipe be flush with floor?

Yes, toilet pipes should be flush with the floor. Toilet pipes are an essential part of your plumbing system, and it’s important to make sure that the pipes are securely attached to the floor in order to ensure a good seal.

In some cases, when a toilet is not properly attached to the floor, leaks can occur in the joint where pipes meet the toilet. In addition, pipes must be correctly positioned and aligned to the floor in order to ensure that the pipes will be able to carry water without obstruction, as well as to reduce the risk of clogging.

If the toilet pipes are not flush with the floor, it can be difficult to make all necessary connections in order to secure the plumbing, and the overall system could be compromised. Therefore, it is essential to make sure the pipes are flush with the floor before attempting any other plumbing work.

What height should plumbing be rough-in?

The height of plumbing rough-in refers to the height at which the plumbing pipes will be located. This includes the distance from the floor to the point where the pipes enter the walls or ceiling. For residential plumbing, the rough-in height is typically 12 inches from the floor for lavatories, showers, and water closets.

For bathtubs, the rough-in height is usually 30 to 36 inches. It is important to note that the rough-in height is measured from the top of the finished floor in the bathroom area. Additionally, it is important to make sure there is sufficient space to allow for the installation of the plumbing fixtures, drainage lines, and any other accessories.

It is also important to consider the future installation of any wall-mounted fixtures or accessories. Finally, it is essential to follow local building codes when planning your rough-in height so that you are in compliance with construction requirements and standards.