Yes, Bemis toilet seats come with a 2-year limited warranty. This warranty covers the toilet seat against breakage due to a manufacturing defect. If the seat is found to be defective during the warranty period Bemis will replace the seat free of charge.
However, normal wear and tear, improper installation or a product incorrectly used or abused are not covered under the warranty. If the product is found to be defective beyond the estimated 2-year warranty, it will be replaced at Bemis’ discretion.
How long should a toilet seat last?
The length of time that a toilet seat will last will depend on the type of toilet seat, the amount of use it gets, and proper maintenance. Toilet seats made of plastic or wood can last between 5 to 7 years when they are well maintained.
If they are not well maintained, the lifespan of the toilet seat could be significantly shortened. Luxury seats made of higher-quality materials will last longer and may even have warranties that exceed 7 years.
To ensure that your toilet seat will last as long as possible, make sure to clean it regularly with warm soapy water and a cloth, and ensure you don’t put too much pressure on it when sitting down.
How do I fix Bemis Statite toilet seat?
To fix a Bemis Statite toilet seat, the first step is to identify where the problem is. If the seat will not stay up, the firmness clip may need to be adjusted. If the clip is too loose, it will not provide the necessary tension to hold the seat in the upward position.
If it is too tight, the seat may be hard to lower after being lifted up. To adjust the firmness clip, you’ll need a flat-head screwdriver. Locate the clip on the underside of the seat and adjust the screw until it is tight enough to hold the seat up, but not so tight that you can’t easily lower it.
If the problem is that the seat wobbles when opened or closed, you may need to tighten the hinge hardware. You’ll need a Phillips head screwdriver to do this. Unscrew the cleat nuts and washers and use the screwdriver to tighten each of the knurled hinge nuts.
When finished, check the seat for level, and add or remove the necessary washers, using the same Phillips head screwdriver, until it is properly aligned.
If the issue persists after following the steps above, it is best to contact the Bemis company for further assistance. They may need to send replacement parts if the seat has broken or become worn over time.
Do toilets come with warranties?
Yes, toilets typically come with warranties. The length and terms of the warranty vary depending on the model and manufacturer, and some may even have extended warranties available. Generally, toilet warranties will cover the inner parts of the toilet, such as the flushing mechanism and flush valves, for a specified period of time (often 1-3 years).
They may also cover the bowl, tank and Seat for a lesser period. Warranties often exclude the finish and any parts subject to wear-and-tear (such as air-filled parts). It’s important to read through the specific warranty details for the model you are considering, as coverage may vary by manufacturer.
Additionally, some companies may offer extended warranties on certain models, so it may be worth checking.
How much does it cost to fix a toilet seat?
The cost to fix a toilet seat depends on the issue that needs to be resolved. If it is just a cosmetic issue, such as a scratched or discolored seat, then you may only need to purchase a new seat, and the cost will vary based on the type and color of the seat you choose.
If the toilet seat has structural damage, such as a loose hinge, broken lid, cracked seat, or chipped bowl, then you may need to hire a plumber to fix the problem. The cost for a plumber to repair a toilet seat can range from $75 – $200, depending on the job’s complexity and the materials needed.
If the toilet seat needs to be replaced entirely, then it could cost between $100 and $300+, depending on the model and materials used.
Who is responsible for replacing a toilet seat?
Generally, the responsibility for replacing a toilet seat is with the homeowner. Replacing a toilet seat is generally a relatively simple task, but it can be useful to consult a professional if you are uncertain about the process.
You will need to gather the correct tools for the job, including a screwdriver and a replacement seat of the correct size for your toilet. Take off the old seat by unscrewing the nuts underneath the toilet where the seat is currently attached.
Install the new seat by placing the bolts into the mounting holes and attaching them to the nuts that hold the seat in place. Be sure to use the appropriate washers when tightening the nuts and bolts.
Can a handyman fix a toilet seat?
Yes, a handyman can typically fix a toilet seat. Depending on the type and condition of the seat, the handyman may need to order and install a new one. In some cases, they can perform a simple repair such as tightening a loose hinge, replacing a cracked peg, or replacing a damaged cushion.
A handyman will assess the toilet seat to determine if the repair is doable and if a new one needs to be installed. They can also make minor repairs to the bowl and tank itself, such as replacing the wax seal, tightening the bolts, and making any other needed adjustments.
Are toilet seats easy to fix?
Repairing a toilet seat is relatively easy and straightforward, though the exact instructions you follow may vary depending on the make and model of your seat. In general, you’ll need to use a screwdriver to remove the screws underneath your seat, lift off the seat, unscrew the plastic ring connected to the underside of the lid, remove the bolts from the hinges, and then reinstall the new seat in a reverse process.
If you’re uncomfortable with completing this task on your own, there are a variety of YouTube tutorials you can watch for guidance, and it’s usually a good idea to consult a plumbing expert if the issue persists.
Is it cheaper to repair or replace a toilet?
Ultimately, it depends on the situation. If there’s just one minor, inexpensive repair, such as replacing a toilet handle or repair a flapper, it’s probably cheaper to do the repair yourself. If the problems are more extensive, it may be more cost effective to replace the toilet entirely.
Other considerations include the age and quality of the toilet. If it’s an older model, a new low-flow toilet, for example, may be more cost effective in the long run, as it will save on water expenses over the long term.
It’s important to do thorough research and balance the current problem against future costs and benefits to see which is the best option for you.
Is it better to top fix or bottom fix toilet seat?
When choosing between a top fix or bottom fix toilet seat, it really comes down to personal preference. However, there are some benefits and drawbacks to consider when making your decision.
Top fix toilet seats are quick and easy to install, as the screws for the fixtures mount through the top of the toilet seat. This can make it simpler to remove and clean the seat. Additionally, since the screws are mounted through the seat, there is less risk of the seat moving when getting on and off.
Bottom fix toilet seats, on the other hand, have screws that attach to hidden fixtures at the bottom of the seat and cistern. This can make installation a little more difficult, but it does not require access from the top, which can be beneficial for some users.
Additionally, since the screws attach to the bottom of the toilet seat, it can result in an even smoother, more even surface.
No matter which type of toilet seat you choose, you should always consider the design and material of the seat, as this will have an impact on the stability, hygiene, and comfort. Both top and bottom fix seats can be extremely durable and long-lasting when the right material is used.
How do I know if my toilet seat needs to be replaced?
If you can visibly see that your toilet seat is no longer functioning properly, it likely needs to be replaced. Signs that it needs to be replaced include:
– Cracks or splits in the plastic
– The toilet seat is discolored or stained
– The hinges are cracked or broken
– The seat is warped or is not sitting flush against the toilet bowl
– A particularly musty smell is coming from it
– The toilet seat is not secure and keeps coming off the bowl
If any of these signs are present, it is likely time to replace the toilet seat. It is important to check the toilet seat periodically for any damage because it can pose a safety risk. If you wait too long to replace it, it could cause potential injury if it unexpectedly gives way or breaks.
How do I keep my toilet seat from sliding sideways?
Keeping your toilet seat from sliding sideways is a common problem that can be easily fixed with the right materials. The best way to do this is to purchase some rubber toilet seat bumpers. These bumpers are small rubber discs that can easily be stuck onto the toilet seat to help keep it in place.
Alternatively, you can also use double-sided tape that is designed to stick to the bottom of the toilet seat to help keep it in place. For an extra secure hold, you can use both rubber bumpers as well as double-sided tape.
Another option, which works especially well on wooden toilet seats, is to use felt pads that can be stuck on the underside of the seat, and then attach a matching piece of felt with a very small amount of glue to the toilet bowl.
This prevents movement and sliding, and should keep the toilet seat in place for many years.
Should I replace a 30 year old toilet?
Replacing a 30 year old toilet is a personal decision, but it might be worth considering. The average life span of a toilet is approximately 10-15 years, so a 30 year old toilet has likely seen its best days.
This can mean it is less efficient, uses more water with each flush, and is at risk for leaks due to aging seals and parts. Installing a new toilet is an inexpensive and easy home project that can make a big difference in water usage and utility bills.
If you’re considering replacing your 30 year old toilet, make sure to research the best models for your particular space and needs. You may also want to factor in any local plumbing codes or restrictions to ensure you get the best fit for your home.
How much should you spend on a toilet?
When it comes to how much you should spend on a toilet, ultimately it depends on your budget and what features you are looking for. Many toilets typically range from around $100 up to $600 or more, depending on the type and features you desire.
Consider what’s important to you – if you want a one-piece toilet with comfort height seating and a powerful flush, then you should budget for a higher end model. If you have a tight budget, consider opting for a two-piece toilet which is usually more affordable, plus easier to install.
Also, you’ll want to ensure your new toilet is the correct size and will fit in your current space. If you need to replace a curved tank, you’ll want to make sure your new model is compatible or purchase an extender.
It’s important to do your research on what would be the best value for the money. Be sure to factor in the cost for any additional installation accessories and make sure to measure twice before you buy.
Do new toilets flush better than old toilets?
In general, yes, new toilets flush better than old toilets. Most new toilets on the market have the ability to flush with greater force and efficiency than older models. New toilets usually feature larger, more powerful flush valves than older toilets, resulting in a more powerful, effective flush that is designed to quickly dispose of waste and rinse the bowl clean.
New toilets may also offer additional features such as dual flush capabilities or efficiency-maximizing flushing technologies that are designed to reduce water usage. As with any purchase, it’s important to read product reviews and carefully research the brand, design and features to ensure you get a toilet with the best possible flushing power for your home.