Skip to Content

Do they make toilets that sit closer to the wall?

Yes, many toilets are designed to sit closer to the wall. A standard toilet typically uses 12” from the wall, but toilets designed to sit closer to the wall can typically use 8-10” from the wall. These toilets are available in a range of styles, from traditional designs to more modern and contemporary designs.

Additionally, some toilets designed to sit closer to the wall use a special tank-type design which allows for a 3” reduction from the wall. This type of toilet is often referred to as a “flush-to-the wall” toilet or a “short projection” toilet.

overall, there are many toilet designs that sit closer to the wall, so you can find one that will work in your bathroom and give you an extra few inches of space.

Do all toilets sit the same distance from the wall?

No, not all toilets sit the same distance from the wall. The distance from the toilet to the wall depends on the type of toilet and your particular bathroom layout. Most toilets are designed to be placed between 15-19 inches from the wall, however this may not be practical for some bathrooms due to the distance between the wall and the water supply pipes or drain.

In those cases, an offset toilet flange may be used to give the toilet the correct distance from the wall, usually anywhere from 5 to 7 inches. Additionally, some toilets, such as corner toilets and wall-hung toilets, are designed to fit snugly against the wall, meaning they will sit closer to the wall than a standard toilet.

Should a toilet sit flush with the wall?

Yes, it is important for a toilet to sit flush with the wall for a number of reasons. First, it helps to create a seamless look in the bathroom, as well as preventing any hard to reach areas from becoming dust traps.

Secondly, when properly installed the space between the wall and the toilet will be waterproof and sealed, preventing any water damage or mold growth that could be caused by leaks. Finally, proper installation ensures the toilet is stable and secure and will not shift or move when used, reducing the chance of accidents or other potential damage.

In order to ensure your toilet is properly installed, make sure to follow the instructions that come with the product. In most cases, the toilet will be attached to the floor with screws and the wall with nuts and bolts.

It is important to get the measurements right and that the parts are all fitted tightly together so the toilet is secure. Any gaps between the wall and the toilet should be sealed with caulk to make sure it is secure and waterproof.

What is the minimum space between toilet and wall?

The minimum space between a wall and a toilet will depend on the dimensions of the particular toilet as they can vary significantly. Generally, the distance between the wall and the toilet frame should be at least 15 inches.

This will provide enough space to adequately install the toilet and ensure that the seat and lid can open properly. Additionally, it is important to ensure the toilet is positioned away from any windows and doors, so that any odors produced are not circulated throughout the room.

What are 2 things you should never flush down a toilet?

Two things that should never be flushed down a toilet are feminine hygiene products and paper towels. Though both are made from paper-like materials, they are not designed to dissolve in water like regular toilet paper.

Flushing either of these items can cause clogs in pipes and sewers, leading to slow drainage, overflowing, and expensive repair bills. Additionally, flushing feminine hygiene products can cause contamination of nearby water sources, and can even be disruptive to marine life in certain areas.

Therefore, it is best to avoid flushing anything other than toilet paper and human waste in order to maintain a properly functioning toilet and sewage system.

Are all toilets 12 inches from wall?

No, not all toilets are 12 inches from the wall. Depending on the model, the distance from wall to the center of the toilet outlet can vary from as little as 8 inches to as much as 14 inches. The exact measurement depends on dimensions of the toilet and can vary by model.

It is important to be aware of this detail when you purchase a toilet for your bathroom, as you may need to make changes to the existing bathroom fixture or plumbing to accommodate the new toilet. Additionally, you should consider the size and shape of the area in your bathroom to make sure there is a sufficient amount of room for your toilet.

Why is the toilet always next to the shower?

The placement of the toilet and shower next to each other is a common trend in modern home designs, and there are three main reasons behind this.

First, having the toilet and shower near each other is practical, as multiple plumbing lines will be needed for both, and keeping them close minimizes the number of runs and simplifies the installation process.

By having these two items close by, one line can carry out the waste from the toilet and fresh water to the showerhead.

Second, having the two fixtures side by side maximizes the amount of space that is available for other features in the bathroom. It can be a great idea to place a vanity or built-in shelves next to the toilet and shower.

This combination takes up the least amount of space in a typical bathroom.

And lastly, having the two fixtures next to each other is convenient and practical. This placement allows users to move back and forth between the two items with ease, allowing them to shower quickly in the morning or completing bathroom activities in one area.

Additionally, there is typically also less cleaning involved when the two fixtures are right next to each other, as less floor space will be exposed.

Overall, the placement of the toilet next to the shower is beneficial due to its convenience, practicality, and space-saving benefits.

Is 2 feet enough room for a toilet?

No, 2 feet is not enough room for a standard toilet. Toilets typically need to be spaced at least 24-30 inches apart to allow enough room for a person to sit and stand. Additionally, industry standards recommend leaving at least 15 inches of free space between the centerline of the toilet and any walls or other obstructions.

Finally, most current codes require at least 15 to 17 inches of clearance between the floor and seat. Taken together, these requirements mean that a standard toilet would not fit in a space with just 2 feet of room.

How far from the wall do you put a toilet flange?

The distance of the flange from the wall depends on several factors, such as the type of flange being used and the type of flooring being installed. Generally speaking, it is best to leave at least 1/4 inch of space between the flange and the wall.

If a cement floor is being installed, a bit more space may be needed. In addition, it is important to ensure the flange is firmly secured to the floor. It should not be too loose or too tight, and should be firmly anchored so it does not move or shift.

How do you install a toilet when the flange is too low?

If the floor flange for the commode is too low, the first step is to either replace it or place a new wax ring below the flange in order to add height. If the flange is not removable, it can be shimmed with a pre-formed wax gasket, which is placed between the floor and the flange.

Make sure to create a perfect seal between the flange and the floor, otherwise the toilet will not be secured properly. Once the flange is level with the floor, the next step is to install the toilet onto the flange.

Begin by placing the toilet onto the floor flange to make sure that it is a snug fit. If needed, tighten the large bolts found at the bottom of the toilet to ensure a secure fit onto the flange. Place the wax ring onto the bottom of the toilet, making sure that it is centered in order to prevent any leaking from the flange.

Next, rock the commode from side to side in order to spread out the wax and help create a seal. To finish the installation, place the washers and nuts onto the bolts and tighten to secure the toilet.

Once the toilet is in place, make sure to test for any leaks around the flange and seal.

Does toilet flange sit on concrete or tile?

The toilet flange typically sits on top of the flooring material underneath the toilet, whether that be concrete or tile. The flange is usually made of PVC or plastic, and has two or three plastic or metal bolts that hold it in place.

It is important to select a flange that is made for the type of material beneath it, because it needs to be able to securely attach to it. For concrete floors, you need to select a flange designed to be used with a concrete subfloor, since concrete is rigid and won’t compress when the screws are tightened down.

On the other hand, for tile floors, you need to select a flange that is designed to fit with a tile floor, since the tile is more flexible and may give when the screws are tightened down. When installing the toilet flange, the bolts need to be tightened enough so that the flange securely attaches to the flooring, but not too tightly or it could end up cracking the tile or concrete beneath it.

What toilet takes up the least space?

Compact toilets are the ideal choice for bathrooms with limited space. These toilets are specially designed to occupy less space than standard toilets and are typically shorter. Many compact toilets are now wall-mounted for extra space savings.

Toilets that use wall-mounted tanks can save up to six inches of room from the back of the toilet which can make quite a difference in a small bathroom. Wall-mounted toilets are great for a modern look, and they create a clean and open appearance in a small bathroom.

Additionally, many compact toilets come with a seat height of only 16 inches, which is slightly lower than standard toilets. This can make compact toilets more comfortable and accessible for people of all ages and sizes.

What type of toilet is for a small bathroom?

For a small bathroom, the most suitable type of toilet is a compact, wall-mounted toilet. These types of toilets are great for saving space because they don’t require a lot of depth to install. As an added bonus, wall-mounted toilets can also give the illusion of a larger bathroom.

You can choose from a variety of styles and colors and there are lots of options with low flow, dual flush, and even models with bidets built in. Additionally, you can install it at the height that is right for your comfort and the height you need to ensure proper hygiene.

Wall-mounted toilets are also typically easy to maintain and clean since they don’t have the small nooks and crannies of other toilet designs.

Do elongated toilets take up more space?

Yes, elongated toilets take up more space than a traditional round bowl style toilet. Elongated toilets can be approximately 2-3 inches longer than a round toilet and the elongated bowl curves out further.

This means they occupy more space in the bathroom and can be a tight fit even in a medium or large sized bathroom. The tank of a standard elongated toilet is typically a half inch to an inch wider than a comparable round bowl model.

Therefore, an elongated toilet will occupy more floor space in your bathroom than a round bowl toilet does.

What is the smallest size of commode?

The smallest size of a commode will depend on the type of commode and where it is being used. Generally, residential commodes come in standard sizes ranging from 15-17 inches in width, while ADA compliant toilets may be 28-30 inches in width.

Public restroom commode bowls can be as small as 8-10 inches in width. However, the size of the tank and the overall height of the commode will further contribute to its size. Toilets can range anywhere from 28 to 34 inches high while tanks can range from 15-20 inches and may be higher depending on the type of toilet.

Additionally, the style of commode or toilet can affect its size and the space it will take up in the bathroom. For example, wall mounted commodes create a more compact unit taking up less space in the bathroom compared to traditional floor models.

Furthermore, some shorter, compact floor models may be able to fit in small bathrooms. When selecting a commode for a small bathroom, it is important to measure the room to ensure that whichever model you choose is going to fit comfortably.