Skip to Content

Do you tile shower curb or wall first?

Tile installation in a shower should start with the wall. The first step is to prepare the shower walls and the area that will be tiled. Once the walls are prepared and waterproofed, it’s time to start placing tiles.

Begin by laying out tile spacers along the bottom of the wall with the tile slightly overlapping into the shower curb. Make sure to use a measuring tape to ensure the tile is evenly spaced and aligned.

Once the tile is in place, use a trowel to spread thinset mortar onto the wall. Then apply the tiles on the wall making sure to use spacers to maintain the spacing. Once the wall is complete, continue tiling onto the shower curb in a similar manner.

Now you have successfully tiled the walls and the shower curb.

What is the correct order to tile a shower?

The correct order to tile a shower is as follows:

1. Prep the Walls – Prep the walls by removing any existing grout and caulk, following the local building codes.

2. Apply a Waterproofing Membrane – After carefully measuring the shower walls, apply a waterproofing membrane to act as a barrier to keep water and moisture away from the drywall.

3. Install the Shower Pan – If a mortar bed is used, lay down a layer of mortar mix and then place the pan in place. If a pre-formed pan is being used, simply place it in the designated area.

4. Install the Tiles – Install backing board on the walls to which the tiles will be attached. Begin tiling the walls in a grid pattern, starting at the highest point of the wall and working down. Apply a layer of thinset mortar to the wall, spread evenly with a notched trowel, and press the tiles into place.

5. Grout the Tiles – After the thinset mortar has dried and the tiles are firmly secured in place, spread grout over the tiles and allow it to dry for 24 hours.

6. Seal the Grout – Once the grout is dried, apply a sealant to keep the grout from absorbing moisture.

7. Apply Caulk – Finally, caulk any seams or gaps between the tiles and walls to ensure a water-tight seal.

When tiling a shower where do you start?

When tiling a shower, it is important to start in the center and work your way out. It is best to start with your largest tiles first, and then finish with the smallest tiles. If you are beginning from the floor, you may want to start by laying out the tiles and measuring to ensure a straight line.

If you are starting from the wall, use a level or a laser to make sure the tiles are straight. You will also need to measure the walls to determine how to lay the tiles. Before you begin tiling, it is important to figure out how much adhesive and grout you need and mix it correctly.

Make sure to use appropriate adhesive and sealants in the shower, and follow the manufacturer’s instructions for application. Additionally, it is important to use a vapor barrier and waterproofpadding before you put down the tiles.

For more detailed instructions, consult a professional tiling contractor or search online for tutorials.

How do you tile around a shower curb?

Tiling around a shower curb is a difficult task that requires patience, planning, and perfect timing. First, you need to ensure that your shower base is completely sealed before you begin. After the base has been sealed, you can measure the height of your shower curb, and make necessary cuts to the tiles to adjust for the curvature.

If your shower curb has a rounded portion, you can use a jigsaw to take care of the cuts.

Once the necessary cuts have been made and double checked for accuracy, you can start laying down your tiles. Before you begin, it’s best to start from the back wall of your shower and then lay your tiles going forward.

To do this, you can use a notch trowel to spread the thinset mortar and place the tile. When it comes time to tile around the curb, you will have to make use of spacers and a tile adhesive to help you achieve the perfect grout lines.

Finally, once you’ve finished tiling around the shower curb, you can then apply the grout around your tiles. Using a float and a bucket of grout, you can spread the grout across the tiles, making sure to use a damp sponge to wipe off any excess.

After the grout has dried, you can then use a sealer of your choice to add a waterproof barrier. If all these steps have been done carefully and in order, then you should have a perfectly tiled shower curb that is ready to be used.

What goes first tile or wall tile?

When tiling a wall, the first step is to prep the surface. This includes making sure the wall is free from dirt, dust, and other debris. Once the surface is prepped, it is important to begin with the floor tile, because it’s the base of all tile work and any wall tile will be installed on top of it.

Floor tiles are typically larger and heavier than wall tiles so it’s best to install them first as they need to support the wall tiles. When installing floor tiles, it’s also important to ensure the grout is properly sealed to prevent water from seeping into the tile.

After the floor tile is installed, then wall tiles can be installed. This can involve several steps, depending on the type of wall tile and the desired effect. Some common steps include adhering the wall tile with adhesive, setting the grout and allowing it to dry, and properly sealing the tile.

Installing wall tile after floor tile also helps to ensure that a uniform look is achieved. By ensuring that the wall tile supports the floor tile and that the same grout is used, a cohesive look is created.

Does a shower curb need to be pressure treated?

No, a shower curb does not necessarily need to be pressure treated. Pressure-treated lumber is designed to resist decay and extend the lifespan of the wood. It’s a good idea to use pressure-treated lumber for outdoor projects where the wood will be exposed to moisture, however, for an indoor shower, pressure-treated wood is not necessary.

You can opt for a non-pressure-treated piece of wood, but keep in mind that it may need to be replaced sooner than if it were pressure-treated. When choosing a wood for your shower curb, make sure it is labeled as being suitable for bathroom use.

You could also choose a waterproof material like tile or marble for the shower curb. Regardless of what material you choose, it should be sealed to help prevent water damage. Additionally, take the time to properly install the shower curb to ensure that it’s sealed correctly so water doesn’t seep through and create water damage over time.

Can you tile a shower right over drywall?

Generally speaking, it is not recommended to tile directly over drywall in a shower. Drywall has a tendency to swell and deteriorate when exposed to moisture from regular shower use, which can cause serious damage.

It is best to install cement backer board over the drywall before tiling a shower to provide a waterproof and reliable surface. Cement backer board is more water-resistant than drywall and provides a stronger surface that is better able to support the weight of the tile.

In addition, it is a good idea to apply a waterproof membrane between the cement backer board and the waterproofing material beneath it to protect the area from water infiltration.

What to put on walls before tiling shower?

Before tiling a shower, the walls should be completely prepared with the right materials. This includes applying a waterproofing membrane, waterproof drywall or cement board, and a primer.

The waterproofing membrane is the most important step and should be applied to all areas of the shower that will be tiled, as well as up the walls beneath the tile line. Make sure to follow the manufacturer’s instructions for proper installation.

Waterproof drywall and cement board are the most commonly used materials for wall preparation and both should be installed according to the manufacturer’s instructions. It’s important to ensure the panels are sealed properly with a silicone caulk or construction adhesive, and that all seams and edges are taped and covered with a waterproofing sealant.

Finally, the walls should be coated with a primer before tiling. This helps the tiles adhere to the wall more effectively and can help seal gaps around the tile line. Be sure to choose a primer that specifically states it is suitable for use in wet areas.

What order do you install a bathroom?

The order in which you install a bathroom depends on the size of the space and the scope of your project. You may need to consult a professional plumber or contractor to ensure you complete the project correctly and safely.

To begin, you will want to ensure that the space has the adequate plumbing and electrical connections. If the space you are working with is already complete with these connections, you can proceed with the installation.

After all utility connections are established, it’s time to install the components of your bathroom. Depending on the type of bathroom you are constructing, this may include a toilet, sink, shower/bathtub, and other fixtures such as a towel rack or shelving.

The installation of the toilet will typically be the first step, followed by the sink. The plumbing for both of these fixtures will connect to the main drain line. It’s important to ensure that the connections are sealed properly, as a leak may occur if these steps are done incorrectly.

Next, you will likely install the bathtub/shower unit. This may involve additional wiring to bring power to the shower, and making sure that the pipes are properly installed to allow water to drain correctly.

The finishing touches will include adding drywall and flooring, as well as painting and installing the various fixtures. Once all of the components of the bathroom have been installed, you can finally use it.

It is important to recognize that the installation of a bathroom can be a time consuming and complex project. If you are unable to do the work yourself, it is best to consult with a professional who can ensure the job is done correctly and safely.

Can you use Thinset in a shower curb?

Yes, you can use Thinset in a shower curb. Thinset is a type of mortar made of Portland cement, fine sand, and water. It is a strong and durable material that is ideal for setting tiles, but is also commonly used as a structural material for building walls and other surfaces.

Thinset is an excellent choice for a shower curb because it is waterproof and provides a strong barrier that won’t crack or chip easily. When installing a shower curb with Thinset, you will want to take extra care to make sure that the walls and floor are flat and level.

It’s also important to layer the Thinset in thin layers, allowing for proper drying time between each layer, and to trowel it correctly so that it is packed tightly into the cracks. Finally, make sure that you allow the Thinset to dry completely before using the shower.

How do you finish tile edges in a shower niche?

When finishing the tile edges in a shower niche, there are a few options to choose from. The most common is to use bullnose tile, which is a rounded edge tile used most often for this purpose. This is an attractive option that creates a smooth transition from wall to floor and comes in a variety of styles and sizes.

However, for a more contemporary look, trim pieces such as a chair rail or quarter round tile can also be used. The chair rail is mounted to the wall and the tile then grouted onto it. Quarter round tiles typically installed on the outside corners of the niche and are great for providing a finished look.

If you have a rounded niche, many manufacturers produce pre-made rounded corner trims and edge trims that attach easily to the tile. They come in a variety of sizes, shapes and finishes, making it easy to match the existing tiles.

Whatever edge finishing option you choose, make sure to consult the manufacturer’s instructions for proper installation.

What is the material for a shower curb?

The material for a shower curb typically consists of concrete, which is poured into a wooden or plastic form, set and shaped to fit the desired size and shape of the curb. For a heavy-duty curb, it is recommended to use concrete with a high-quality sealer applied over the surface.

This ensures it is waterproof and will last a long time. For a more decorative look, the concrete can be tiled, painted, or finished with a variety of materials, such as natural stone, brick, marble, or tile to give it a unique look.

What is the difference between a shower curb and threshold?

A shower curb is a raised ledge built into the base of a shower, typically made of concrete, tile, marble, or other water resistant material. Its purpose is to contain any stray water that splashes out of the shower area, keeping it contained and away from any adjacent surfaces.

The shower curb usually has a lip of about 3 inches to 4 inches high so the water does not flow out of the shower.

A threshold, on the other hand, is a transition piece located at the entrance to the shower, usually made of the same material as the shower curb. They are designed to cover the gap between the shower floor and the bathroom floor, and help to provide a smooth transition from one area to the other in order to prevent water from spilling out.

The height of the threshold is usually around 1 inch. Thresholds can also act as a decorative finish to a shower, providing a uniform and visually appealing boundary.

Do you nail in cement board for shower curb?

Yes, you can nail in cement board for a shower curb. However, the most common and recommended way to secure cement board into place is to use a cementitious adhesive, rather than nailing it. This allows the cement board to adhere firmly and completely to the subfloor, providing a more solid and durable foundation.

Additionally, nailing can damage the underlying subfloor, and can weaken the connection between the cement board and the subfloor. Installing cement board for a shower curb does require precision and care to ensure that the installation is secure.

Before installing, it is important to clean the subfloor and make sure that the mortar bed is applied with an even layer. Once the cement board is in place, use the cementitious adhesive and a trowel to ensure that it is adhered securely.

Finally, seal the corners and seams of the cement board with cementitious tape to ensure a waterproof seal.

How does water stay in a curbless shower?

Water stays in a curbless shower due to a number of different design elements. First, a curbless shower typically includes a shower pan, which is a waterproof liner that goes beneath the shower floor/ground.

This ensures that all of the water remains contained in the shower pan. Additionally, a curbless shower usually has a sloped design that directs water towards the drain. By sloping the floor of the shower, it allows the water to make its way to the drain without accumulating or overflowing.

The direction of the sloping should always be towards the drain in order to maximize the drainage ability of the shower. Finally, some curbless showers also come equipped with an additional waterproof sealant such as a silicone-based sealant around the perimeter of the shower.

This helps to ensure that no water will seep outside the walls of the shower and cause any water damage or growth of mold or mildew. With these design elements in place, water stays in a curbless shower and is effectively drained away.