Skip to Content

Does rough-in have to be exact?

No, rough-in does not have to be exact. Rough-in refers to an earlier stage in the plumbing process, when the wall and ceiling cavities are framed and outlets, fixtures, vents, and other components are installed.

At this stage, it is important to make sure everything is placed in the right spot, but the exact measurements only need to be precise enough to know where these items will be placed and that there is sufficient space for them.

After rough-in is complete, the components will need to be fastened securely in place and the plumbing pipes and fittings can then be adjusted and connected to ensure a precise and secure fit.

What is considered a rough in?

A rough-in is a plumbing term used to describe the installation of the plumbing fixtures and pipes prior to the installation of walls, tiling, and other components that are used to finish the space. This includes the installation of the plumbing supply lines, waste lines, vent stacks, and shutoff valves.

It also includes installing the drainage pipe, water closet supports, and valves. The rough-in is often completed before any of the other construction activities begin, as it is difficult to move some of the pipes and fittings once walls and other components are in place.

This process also helps to ensure that the plumbing will be installed properly and that any potential issues can easily be identified and rectified before proceeding with the finishing work.

Can you replace a 12-inch rough in toilet with a 10-inch rough in toilet?

Yes, it is possible to replace a 12-inch rough in toilet with a 10-inch rough in toilet. However, it is important to first assess your space to make sure the smaller 10-inch toilet will properly fit.

You should also measure your current 12-inch toilet to confirm that you are choosing the correctly sized replacement.

Before replacing your toilet, you will also want to be mindful of the location of other fixtures such as the drain and water pipes. The location of these should be taken into consideration when purchasing a toilet in a smaller size as they may need to be repositioned to fit the new toilet.

It is also important to have the right tools on hand to complete the replacement. This includes items such as a plumbing wrench, pliers, and a screwdriver, amongst other things. Doing so will ensure the process is smooth and efficient, and your new toilet is properly and securely installed.

What does 12-inch rough in for toilet mean?

12-inch rough in for toilet typically refers to the distance between the wall behind the toilet and the center of the drain pipe in the floor. This measurement is usually 12-inches, though it is sometimes 11-inches or 13-inches.

The rough in determines the size and shape of the toilet that can be used and ensures the drain pipe and the flange on the toilet are properly aligned. Many toilets are made with different sizes of rough-ins.

It is important to measure the rough-in to ensure the correct size toilet is purchased. Often the wrong size toilet cannot be returned and it can be difficult to make a smaller toilet fit a larger rough-in, so it is important the rough-in measurement is calculated accurately from the beginning.

How do I know if I have a 10 inch or 12-inch rough in toilet?

To determine if you have a 10 inch or 12-inch rough in toilet, you will need to measure the distance from the wall behind your current toilet to the center of the waste pipe that the toilet is connected to.

A 10-inch rough in toilet will measure approximately 10 inches from the wall to the center of the waste pipe, while a 12-inch rough in toilet will measure approximately 12 inches from the wall to the center of the waste pipe.

Additionally, you can check the product label on the toilet to see what size it is. If the label does not indicate a specific size, you can measure the distance from the back of the toilet to the center of the waste pipe.

If you still cannot determine the size, you can contact the manufacturer to get specific dimensions on the particular make and model.

Should toilet flange be flush with floor?

Yes, the toilet flange should be flush with the floor. This is so the toilet is securely and properly affixed to the plumbing and sewer lines. The installation of a toilet requires a solid and level flange to properly set the toilet and ensure a good seal to keep water and gasses from escaping.

Additionally, you can use shims or wax rings to level any unevenness in the floor after the flange is secured into place. If the flange is not level and flush with the floor, it will be difficult to make the necessary adjustments.

Therefore, it is important to make sure the toilet flange is leveled and flush with the floor before the toilet is set onto the flange.

How many inches should a toilet be off the wall?

The actual space requirement between the wall and your toilet will vary depending on the size of your toilet and the size and layout of your bathroom. Generally speaking, most toilets should be installed between 12 and 15 inches off the wall.

Smaller bathrooms may require the toilet to be even closer to the wall, while larger bathrooms may allow up to 18 inches of space. Of course, the closer the toilet is to the wall, the tighter the space can be, but it is important to consider how much space you will need to make it comfortable for the user.

It is best to make sure you have enough clearance to safely and comfortably move around the toilet and make any necessary plumbing repairs. Furthermore, having at least some clearance between the toilet and the wall can help to prevent the spread of germs and pathogens from the wall to the toilet.

How far does a toilet stick out from the wall?

Typically, a toilet sticks out from the wall anywhere from 12 to 17 inches. The exact distance can vary depending on the size and design of the toilet, and whether or not it is a tankless toilet or one with a tank.

The distance may also depend on the type of wall the toilet is installed on and any additional accessories that need to be connected, such as a bidet or toilet paper holder. It is important to measure the distance from the wall before installing a toilet, as it may be necessary to adjust the space for a proper fit.

Does toilet rough-in size matter?

Yes, toilet rough-in size does matter. Toilet rough-in size is the distance from a finished wall to the drainpipe at the base of the toilet. This measurement is important because if the toilet is too close or too far from the finished wall, the toilet will not be properly sealed, causing leaks, water damage, and inefficiency.

Most recently installed toilets have a standard rough-in size of 12 inches, though other common sizes are 10-inch, 14-inch and 16-inch rough-ins. To ensure that the toilet you are purchasing is the correct size for your bathroom, measure the current rough-in size or check with a plumbing professional to determine the proper measurement.

What’s the difference between a 10 inch rough-in a 12 inch rough-in toilet?

The difference between a 10-inch rough-in and a 12-inch rough-in toilet is the distance from the wall behind the toilet to the center of the waste outlet pipe beneath the toilet. The 10-inch rough-in typically measures anywhere from 9 7/8 inches to 10 ½ inches, while the 12-inch rough-in measures anywhere from 11 7/8 inches to 12 ½ inches.

If you’re replacing an existing toilet, you need to measure the distance from the wall behind the toilet to the pipe. It’s important to get the right size to ensure that the toilet is secure and properly installed.

If you’re installing an entirely new toilet, you can measure the amount of space you’d like to center atop the waste pipe and buy the appropriate size.

When it comes to size, make sure you measure the rough-in size properly. If you’ve just replaced the toilet and didn’t check the rough-in size, the new toilet won’t fit properly and you’ll have to purchase the correct size to install in its place.

Can you install a toilet in a basement without rough-in?

Yes, it is possible to install a toilet in a basement without a rough-in, but there are some considerations to take into account. If you’re planning to install a toilet without a rough-in, it would be best to find a toilet that is specifically designed for that purpose, such as an upflush or macerating toilet.

These type of toilets have a pump built in that forces the waste up and out of your basement. Alternatively, you can install an angled toilet, but it can reduce the length of your toilet bowl and seat, and make it less comfortable.

Aside from the type of toilet, you’ll need to make sure that the basement has sufficient electirical outlets, as the pump in an upflush or macerating toilet requires electricity to be operated. You’ll also need to ensure that the floor below the toilet isn’t too weak to hold the weight of the body and installation.

Lastly, you’ll need to decide on how to run the waste pipe out of your house into the external sewage system. It’s best to contact a plumber to help make sure that the installation is done properly and safely.

How do you measure the rough-in?

Measuring the rough-in for a project requires measurements to be taken from the existing walls or surfaces of the space. This includes measuring the vertical and horizontal distance between walls or vertical objects, such as studs or posts, as well as the vertical distance between the floor and ceiling in each space.

Additionally, you will need to measure the widths of door frames and the distance between any points where two walls meet in the same plane.

Once all the measurements have been taken and recorded, you will need to create a floor plan or diagram that shows the walls, doors and windows, as well as other important objects in the space. You can use a pencil and graph paper or use a computer program to create a detailed, precise diagram.

From this diagram you can measure the rough-in from different angles and points of reference. With the precise measurements you can be sure to get the largest, most efficient use of the space.

What does rough-in mean for shower?

Rough-in is the step in the installation process which involves readying the plumbing and electrical systems for the shower. This includes installing the necessary pipes, drains, faucets and valves. In the case of electrical work, it includes running wiring, installing light fixtures and switches, and verifying that the GFCI receptacles are working properly.

In order to ensure the shower will function properly and safely, the rough-in work must be completed accurately and thoroughly. Afterwards, the floor and wall surfaces can be installed and further finishing work completed.

What is the most common toilet rough-in size?

The most common toilet rough-in size is 12 inches. This is measured from the wall to the middle of the standard waste outlet. Measuring the rough-in size prior to purchasing a new toilet is important, as it will ensure that you purchase a toilet that fits properly in the space you have available.

While 12 inches is the most common rough-in size, some older homes may have a 10- or 14-inch rough-in size. Therefore, it is important to measure your existing rough-in size from the wall to the center of the waste outlet to determine the correct size of toilet for your space.

Is toilet rough-in from finished wall?

No, toilet rough-in does not refer to a finished wall. Toilet rough-in is the distance from the wall behind the toilet to the center of the hold-down bolts that attach the toilet to the floor. The standard distance is generally 12 inches, but it can vary based on model and type of toilet.

Most toilets require this distance during installation, because the tank must be able to fit snugly against the wall. Some toilets feature “slender tanks” that allow for a decreased rough-in measurement, generally 10 inches.

It is important to calculate the distance of your rough-in before purchasing a toilet to make sure it fits properly.