Skip to Content

How big does a plumbing chase need to be?

The size of a plumbing chase will depend on the particular project. Generally, a plumbing chase should always be wide enough and high enough for the items being placed within, as per local building codes.

For most projects, this is usually a minimum of 4 inches wide and 12 inches high. However, for larger items such as water heaters or boilers, you may need to go up to 8 inches wide and 24 inches high.

It is important to check local building codes to ensure you are meeting the necessary code requirements. Additionally, when creating a plumbing chase, it is important to make sure it is fully enclosed and to use a fire-resistant material such as brick, cinder block, or metal pipe.

What is a chase wall?

A chase wall is a framing technique used in the construction and remodeling of walls and ceilings. It is composed of two boards running parallel to each other and perpendicular to the studs of a wall or joists of a ceiling.

A third board known as a “chase” runs between the two boards, creating a framed space. This space is often filled with insulation or other materials, such as wiring or ductwork. The purpose of a chase wall is to create a barrier between two different sections of a wall or ceiling, allowing for a separation of trades, such as electricians, plumbers, and carpenters.

It is also used for the installation of fire-resistant materials, for aesthetic purposes, and for creating a firestop between two floors.

How do you install a water closet carrier?

Installing a water closet carrier is a straightforward project that can be done by most do-it-yourselfers. Here is a guide to help you get started:

1. Begin by preparing the closet flange. Use a hacksaw to cut off the old flange. Be sure to measure twice and cut once, to avoid any unnecessary sizing issues.

2. After cutting off the old flange, you’ll need to attach the new water closet carrier. Place the carrier onto the closet flange, and then attach the top bolts to secure it firmly in place.

3. Once the water closet carrier is secure, you’ll need to reattach the water supply lines. Place the mounting bolts through the holes in the water supply lines, and thread the washers and nuts onto each bolt.

Carefully tighten each nut until the connection between the flange and the water supply lines is secure.

4. Finally, it’s time to reattach the toilet bowl. Place the bolts through the holes in the toilet bowl, and thread on the washers and nuts. Once each bolt is tightened with a wrench, the toilet bowl should be firmly in place.

Follow these steps to securely install a new water closet carrier, and enjoy the results!

How wide is a wall chase?

A wall chase is a slot or channel cut into the wall to allow for cables and wires to be routed in a clean and safe manner. The size of the wall chase depends on the type of cables or wires you are running and the space you have available within the wall.

Generally speaking, a standard wall chase size is either 2 inches or 4 inches, although sizes can vary depending on your particular needs and requirements. When cutting the wall chase it is important to be sure that it is wide enough to contain all of the cables or wires that you need, but at the same time not to be too large or else it can create an eyesore or a potential trip hazard.

Ultimately, the best way to determine the proper width for a wall chase is to first measure and determine the size of the cables and wires you need to run, and then account for the necessary clearance.

That way you can ensure that your wall chase is the right size for the job and that it looks good and is safe.

What are the 3 standard rough in distances of water closets?

The three standard rough in distances of water closets are 12 inches, 10 inches, and 14 inches.

The standard 12 inch rough in measurement is the most commonly used, and it is typically used for larger bathrooms where there is more space to work with. This allows for more freedom when selecting a water closet, as many brands make toilets that are designed to fit this size.

The standard 10 inch rough in is designed to fit more compact spaces. This rough in size is most commonly used in smaller, less spacious bathrooms, as it allows for more space-saving solutions and fits a more narrow range of water closet styles.

The standard 14 inch rough in is the largest of the three measurements and is usually used for extra-large bathrooms where there is ample room for installation. This size offers the extra width necessary for installing a wider variety of water closets that may not fit the other two sizes.

Does closet flange go inside or outside pipe?

It depends on the type of flange that you are using. Both “inside-fit” and “outside-fit” closet flanges exist, so the answer will depend on which one you are using.

An “inside-fit” closet flange is designed to fit inside a cast iron pipe, so it will go inside the pipe. This type of flange is often used in older homes that may have cast iron wastewater pipes.

An “outside-fit” closet flange is designed to fit over the top of a PVC pipe. This means that the flange will go outside the pipe and provide a base for the bowl of the toilet to sit on. This type of flange is the most common type used in modern homes that have PVC wastewater pipes.

In general, you should use the type of flange that was recommended in the installation instructions, as this should help ensure that you meet all safety and building codes.

What is the difference between a chase wall and a shaft wall?

A chase wall is an open-backed wall constructed of wood, metal, or masonry, which is used to serve as a housing for utilities or other services. The chase is made from two parallel vertical sides and a crossbar, leaving an opening between the sides to run pipes, ducts, conduit, etc.

Chase walls are often used outdoors to protect utilities, provide convenient access, and save space.

A shaft wall on the other hand is a primarily solid wall that encloses an area. It is usually constructed of metal, drywall, or other materials and is used to divide an area such as in a building. A shaft wall is usually much taller than a chase wall and often runs the full length of the space it is dividing, while a chase wall is typically limited to the housing of the utilities.

Shaft walls are used to divide living and non-living areas, such as fire walls, or to separate utility or service areas from occupied areas in a building.

How do you build a chase wall?

Building a chase wall requires careful planning, intricate design, and sturdy materials. Here are the basic steps to constructing a chase wall:

1. Create a blueprint: First, you should outline the design of your chase wall and sketch a blueprint. The blueprint should include a scale of measurements, details of the structure, and a clear diagram of how the chase wall should look when finished.

2. Calculate the dimensions: Based on your blueprint, calculate the number of blocks you’ll need, their size, spacing, and the thickness of your chase wall.

3. Order materials: Depending on your design, you’ll need to order the blocks, mortar, rebar or other materials for your chase wall.

4. Dig and level the base: Depending on the weight of the chase wall, you’ll need to dig and level the base of your chase wall. This will help to provide support. Make sure to use gravel and a landscape fabric to ensure a smooth base.

5. Lay the blocks: Now you can start laying the blocks of your chase wall. Apply mortar to the back of each block and the base and press into place. Continue until you build the desired shape of your chase wall.

6. Add rebar or reinforcements: This step is optional but recommended for sturdier walls. Insert rebar or reinforcements into the blocks for additional support.

7. Fill in with mortar: Once the blocks are in place you can fill in with mortar and make any minor adjustments if necessary. Make sure to fill in any joints and seams completely.

8. Allow wall to cure: Finally, allow the chase wall to cure for an appropriate amount of time before use. This is especially important for any exterior chase walls.

How long does chasing walls take?

Chasing walls can take anywhere from a few hours to a few days, depending on the complexity of the particular wall and how much structural work or repair is required. Additionally, factors such as how much material needs to be cut, how much debris needs to be removed, crawlspace assessability, and the rate at which mortar needs to further dry and set, can all affect the timeline.

If it’s a relatively simple wall, chasing the walls can be accomplished in a few hours. On the other hand, if the Chaser is dealing with larger, multi-dimensional surfaces or significant structural damage, the process may take up to several days.

Ultimately, the amount of time devoted to chasing walls will depend on the unique need and scope of the particular project.

What is the filling for chases?

Chase is a popular British dessert traditionally made from apples, but there are many different types which can include blackberries, rhubarb, plums, gooseberries and other fruits. The traditional filling for a chase is apples, which are peeled and then cooked with sugar and butter before being layered with pastry, usually a light, buttery puff pastry.

Once the pastry is in place, more fruit can be added to the top for added sweetness and texture. The pastry is then brushed with an egg wash and baked until golden brown. A chase is served on its own or with creamy custard, cream or ice cream.

What do you fill wall chases with?

Wall chases are hollowed-out channels in walls and ceilings that are used to run wires and other services. The type of material you need to fill a wall chase will depend on what you are using it for and the size of the chase.

Typically, it is recommended to fill the chase with either non-combustible insulation, fire-rated foam, or expanding foam. Non-combustible insulation is usually inexpensive, easy to cut, and much less messy than foam.

Fire-rated foam is more expensive and harder to cut, but it can provide better soundproofing and additional fire protection. Lastly, expanding foam is quick, easy to use, and provides excellent thermal insulation.

Make sure to choose the right material for your application to ensure safety.

How much does it cost to chase pipes into a wall?

The cost of chasing pipes into a wall depends on a number of factors, such as the size and type of pipe, type of wall, and access requirements. If a wall needs to be opened up, the cost will most likely be higher.

Labor costs can also vary due to the complexity of the job and other factors, such as the amount of pipework to be chased and access requirements. On average, hiring a professional to chase pipes into a wall can cost anywhere from $50-$150 per linear foot.

This price can increase depending on the type of pipes being used and complexity of the job. Additionally, some property owners experience added costs for materials such as fittings, pipes and sealants.

It is also important to factor in the cost of any possible repairs caused by the chasing process, such as plastering or drywall work. It is always recommended to contact a professional to get an accurate quote for the chasing process.

What is a fixture carrier?

A fixture carrier is a device that is used to mechanically hold and support a fixture or workpiece during the machining process. They are typically used in machining centers or drilling and tapping machines, and they are designed to securely hold the workpiece in place during operations such as drilling, tapping, and reaming.

Fixture carriers usually come in the form of fixtures, clamps, or vacuum chucks, and they can be made of various materials such as steel, aluminum, and plastic. Fixture carriers are also designed to maintain workpiece repeatability and accuracy by providing a secure, stable platform for the workpiece to rest on.

They also help reduce chattering, vibration, and thermal drift from the machining process.

How do toilet carriers work?

A toilet carrier is a device that helps to support the weight of the toilet bowl on the waste stack during and after installation. It is generally needed when the toilet bowl and waste stack are not perfectly aligned, which can occur during a rough installation.

The carrier is placed between the toilet bowl and the waste stack, and its adjustable brackets can be used to provide the necessary support and uniform elevation until the necessary adjustments can be made.

Once the alignment is satisfactory, the bracket typically needs to be secured to the wall. Some models of toilet carriers come pre-designed with adjustable feet, allowing for easy installation and adjustment.

Additionally, certain models have built-in water-saving features, such as adjustable or removable overflow channels and flush valves. This helps to reduce water waste, which is important for conserving natural resources.

What is a fixture in real estate terms?

A fixture in real estate terms is any item that has been attached to a property or home in a permanent manner. Common examples of real estate fixtures include carpeting, light fixtures, cabinetry, kitchen or bathroom appliances, or any other type of feature that is attached to the property.

In most cases, fixtures become part of the property and are sold along with the property and included in the purchase price. In some cases, when a buyer is purchasing an existing home, they will also purchase the items that are considered to be fixtures.

Depending on the location and whether these items are considered personal property or fixtures, they may be included in the purchase of the property or sold as separate items.