Skip to Content

How do I fix the feeler arm on my LG ice maker?

To fix the feeler arm on your LG ice maker, you will need to locate the defective part and replace it with a new one. First, identify the arm by visual inspection. It usually has a flat or curved metal arm that connects to the ice tray inside the ice maker.

Once you have identified the arm, open up the ice maker unit. This is usually done by removing a few screws on the back of the unit. Then, disconnect the wires that are connected to the arm.

With the arm disconnected, it’s time to remove the defective part. The arm is held to the unit with a retaining clip. Using a small screwdriver or a pair of pliers, carefully remove the clip and take out the defective arm.

Now, you can install a brand new arm. Slide the new arm onto the retaining clip and make sure the wires are connected properly. Reassemble the ice maker unit and you should now be all set.

If you need help finding the correct replacement part for your particular ice maker, contact the LG customer service department. They will be able to provide you with the correct part and help you with any additional steps.

How do I reset my ice maker arm?

If you need to reset the arm of your ice maker, the first step is to unplug your refrigerator and check the wiring. Ensure that all of the wires are properly connected; if not, reconnect them before proceeding.

Next, locate the water line connected to the ice maker and ensure it is properly connected and closed tightly. If there is a water shut off valve connected to the water line, make sure it is in the open position.

In some cases, the arm will need to be manually reset. To do this, find the ice maker reset button, then hold the reset button for 10 seconds. The arm should then be moved to the “on” position. Once the arm is set to the “on” position, you can then plug the refrigerator back in.

If your ice maker still won’t produce ice, you may need to check the evaporator coil instead. If the evaporator coil is dirty, it may not be cooling correctly, causing the ice maker to not work properly.

Make sure to thoroughly clean the evaporator coil with a soft-bristled brush and vacuum cleaner. Also, check for any clogs or blockages in the water line and make sure the shut off valve is in the open position.

Once these steps have been completed, you should be able to reset the arm and get your ice maker up and running again.

How does ice maker feeler arm work?

The ice maker feeler arm is a component found in many refrigerator ice makers. It is a metal or plastic lever that extends out of the ice maker assembly and sits in the ice bin. With this arm, the ice maker is able to sense when the bin is full.

As ice builds up in the bin, it pushes the feeler arm up, blocking the ice maker from creating more ice cubes. This stops the ice maker from overfilling and prevents water from leaking out. When the ice level drops and the arm drops down, the ice maker is able to produce more cubes.

This process is repeated until the desired level of ice is reached. The feeler arm is sometimes referred to as an ice level arm, probes arm, or ice maker arm.

Why does the arm on my ice maker keep getting stuck?

The arm on your ice maker could be getting stuck for several possible reasons. Firstly, the arm could be broken or malfunctioning due to a manufacturing defect, or loose wires and connections that need to be tightened up.

Secondly, the arm could be getting blocked by a piece of ice or debris stuck inside the ice maker chamber that needs to be cleared away. Lastly, the arm could be getting stuck due to the build-up of ice or water blocking the arm’s movements.

In this case, it’s necessary to empty the ice chamber and remove any obstructions in order to make sure the arm can move freely again.

How does the arm work on an ice maker?

The arm on an ice maker controls when the ice is harvested from the ice cube tray. The arm is connected to a thermostat which passes an electrical signal to the arm when the ice has frozen and needs to be harvested.

The electrical signal opens a set of contacts in the arm, which allows electricity to flow to the harvest mechanism. The harvest mechanism activates a heating element which warms up the metal ejector bar attached to the ice cube tray, causing it to expand.

The expanding ejector bar then pushes up on the ice cubes, popping them out of the ice cube tray and into the collection bin. Once the ice cubes have been harvested, the arm will turn off the electrical signal and the harvesting process will end until the ice reaches the right temperature again.

Why is my ice maker arm stuck in up position?

It is possible that the ice maker arm is stuck in the up position due to a defective ice maker assembly. This could be caused by a blocked fill tube or a kinked water line. It could also be due to a faulty switch inside the assembly which is responsible for lowering the arm when the ice is made.

The switch may be stuck in the closed position, preventing the arm from lowering. To determine the exact cause of the issue, it may be necessary to disassemble the ice maker and check the components.

Other potential causes of the arm being stuck in the up position could include a faulty heating element, a lack of water pressure, or a buildup of ice in the chute. Checking these components as well should resolve the issue.