Putting your Swiffer Wet Jet together is quite simple! Firstly, you’ll need to make sure that you have all the necessary parts; the mop, a bottle of the Swiffer cleaning solution, the inbuilt scrubber, two AAA batteries, and any attachments you choose to use.
Begin by attaching the mop handle to the back of the mop head. Then, attach the inbuilt scrubber to the back of the mop head – it fits into the small gap. Open up the battery compartment at the top of the mop handle, insert the batteries and replace the battery cover.
Next, open the flip cap on the bottom of the mop head and attach the cleaning solution bottle. Twist it into the mop head until it clicks into place. Then, depending on the type of Wet Jet you have and the attachments you are using, you may need to do further assembly.
For example, if you are using the PVA mop head then you will need to attach it to the mop head. This is done by slipping the two slots on the mop head over the grooves on the back of the PVA mop head.
Finally, flip the mop head up and press the trigger. If all has been done correctly then you should get the familiar green light indicating that your Wet Jet is ready for use.
How do you put the head on a Swiffer?
To put the head on a Swiffer, start by unscrewing the top connector. Pick up the head assembly and locate the part of the frame that grips the head pieces. With the handle laying flat, insert the upper part of the head assembly into the top of the handle.
Push down until it snaps into place. Then push the bottom part of the head assembly into the lower connection of the handle. Twist it to the right to secure it. Once the head is securely in place, you’re ready to begin cleaning!.
Which side of the Swiffer Wetjet pad goes down?
The side of the Swiffer Wetjet pad that should be facing downwards when attached to the mop is the one with the green scrubbing pad on it. This is the side that is meant to do the majority of the cleaning work.
It is important to make sure this side is the one facing downwards when attaching the pad to the mop, as the other side is specially designed to not pick up dirt and debris when it comes into contact with the floor.
When the pad is attached properly, the scrubbing pad should run parallel to the floor to ensure the best results.
How do you fix a Swiffer Wetjet that won’t spray?
If your Swiffer Wetjet won’t spray, there are a few things you can do to try and troubleshoot the issue. The first thing you’ll want to do is to turn off your Wetjet, disconnect it from any power source, and lay it down on a flat surface.
You’ll want to then check the battery compartment, making sure that the batteries are securely connected and inserted in the correct way. If the batteries seem secure, you should try replacing them with new ones.
Additionally, you’ll want to check the filter and nozzle for any clogs or blockages. You can do this by unscrewing the filter located at the top of the tank and cleaning out any residue that may be blocking the air flow.
Additionally, you may want to wipe around the nozzle to ensure there are no clogs. Once everything is cleaned and secure, you can try turning the Wetjet back on and test out the spray. If the problem persists, you may have to contact Swiffer’s customer service line for additional support.
How do you take apart a Swiffer Wet Jet handle?
Taking apart a Swiffer Wet Jet handle is a relatively simple process that requires a few basic tools. You will need a flathead screwdriver, needle-nose pliers, and possibly a drill.
Step 1: Remove the handle from the Swiffer Wet Jet. Do this by pinching the clips located around the Swiffer Jet with the needle-nose pliers and pulling the handle away.
Step 2: Use the flathead screwdriver to unscrew the three small screws located around the handle’s exterior.
Step 3: Loosen the handle by gently pulling on it and unscrew it from the remainder of the handle shaft.
Step 4: To remove the handle’s interior, use a drill to make two small holes in the plastic handle. You should now be able to pull apart the handle to reveal its internal parts.
Step 5: Carefully take apart the handle, remove any desired parts, and reassemble the handle before reattaching it to the Swiffer Wet Jet.
How do you assemble a Swiffer Duster?
To assemble a Swiffer Duster, you’ll need to first remove the duster head from the package and insert it onto the Swiffer handle. To do this, hold the Swiffer handle with the clip facing up, and slide the duster head onto the handle.
Push it down until you hear it click, then rotate it to the closed position.
Once you have the duster head assembled, you can attach a disposable duster pad. To do this, open the duster head and place the pad onto the pointed teeth. Close the duster head, and pull the tab at the end of the handle so the pad tightens around the handle.
Your Swiffer Duster is now ready to use. For best results, change the duster pad when it starts to look dirty.
Why is my water spray not working?
It’s possible that there may be a few different causes for your water spray not working. First, make sure to check that there is an adequate supply of water for your unit and that no pipes or hoses have become blocked, clogged, or damaged.
Additionally, you might need to check if the pump is properly installed and if the water pressure is sufficient. It’s also worth checking that all necessary valves are open and that the switch controlling the water supply and pump are all in the “on” position.
If all of these things have been checked and remain in order, then there could be a problem with the pump or the power supply. Check to make sure the power cable is connected properly and then try resetting your circuit breaker just in case there is an electrical fault.
Alternatively, if the pump is no longer working properly, you’ll need to replace it to restore functionality to your water spray unit.
How do Swiffer wet pads work?
Swiffer wet pads are a great way to quickly and easily clean any hard surface area in your home. The pads soak up dirt, dust, and grime while lifting away messes. The layers of the pad work together to break up and dissolve dirt and dirt particles, while the absorbent core helps hold onto them.
Once the pad is saturated it can be thrown in the trash, no rinsing or wringing required. The pads are easy to use, just attach to a Swiffer wet mop handle and you are ready to go. To use, move the mop in a systematic back and forth motion to help dislodge and remove surface dirt, dust and debris from your floors and other surfaces.
Do not rinse the pad or use on unfinished, oiled, or waxed wooden boards, non-sealed tiles or carpeted floors. The wet pads can also be used on appliances, countertops and other surfaces for light cleaning.
Once finished, the used pad should be discarded.
Can you take the top off a Swiffer Wet Jet bottle?
Yes, it is possible to take the top off a Swiffer Wet Jet bottle. To do so, simply find a flat-head screwdriver that fits inside the slot in the middle of the top. Gently turn the screwdriver counter-clockwise until the top comes off.
If necessary, press down on the top while turning until it comes loose; however, exercise caution while pressing to avoid applying too much pressure and breaking the plastic top. Once off, you can clean the bottle and replace the top.
Make sure to turn the top clockwise to secure it back on the bottle.
Where is the battery compartment on an older Swiffer Wet Jet?
The battery compartment on an older model Swiffer Wet Jet is located on the back of the handle, just below the trigger. Simply press the release latch button on the side of the handle, then swing the handle open.
Inside you will see the battery compartment, which holds four AA batteries. Make sure to align the + and – symbols as indicated on the inside of the battery compartment when installing the batteries.
Why is my new Swiffer WetJet not spraying?
If your Swiffer WetJet is not spraying, the first thing to check is the water tank. Make sure it’s filled to the right level and that the tank is firmly attached to the handle. Also make sure the nozzle is clean and not blocked with dirt or dried detergent.
If that doesn’t solve the problem, try removing and reattaching the trigger button to the handle as sometimes this connection can get loose. If your WetJet is still not spraying, check the battery connection.
The batteries can slip out of place and prevent the WetJet from spraying. Lastly, try replacing the batteries and confirm that the trigger button is working correctly. If none of these solutions work, you may need to contact the Swiffer customer service team for further assistance.
How do you remove the batteries on a Swiffer Wet Jet battery compartment?
To remove the batteries on a Swiffer Wet Jet battery compartment, you need to locate the battery compartment. It is typically located on the side of the handle near the bottom. Once you locate the compartment, use a flathead screwdriver to carefully lift up the latch.
You should then be able to use the screwdriver to remove the battery compartment cover. Then, you can take out the dry cell batteries and replace them with new ones if needed. You can then turn the battery compartment cover back to its original position and make sure it is secure.
Finally, you should test the Swiffer Wet Jet to make sure the batteries are working properly.
How do I change batteries in an older model of Swiffer Wet Jet?
To change batteries in an older model of Swiffer Wet Jet, you will need a screwdriver and four AA batteries. Begin by pressing the release button on the back of the Swiffer. This will open the battery compartment and allow you to remove the old batteries.
Next, remove any screws that are visible and lift off the top of the Swiffer. If the model has a plastic upper casing, use your screwdriver to remove any screws. Once the top is off, you can remove the old batteries and replace them with the new ones.
Ensure that all batteries are correctly aligned in the compartment. If your model of Swiffer Wet Jet has a circuit board, make sure that the electrical connections are securely attached to the board.
Once the batteries have been properly placed, replace the back of the Swiffer and secure any screws that you removed earlier. Finally, press the release button to close the compartment and check that the batteries are working.
Does the older Swiffer WetJet have batteries?
No, the older Swiffer WetJet does not use batteries. It uses AAA batteries, which are readily available in most supermarkets and online stores. The newer Swiffer WetJet uses rechargeable batteries, so there’s no need to buy replacement batteries.
The rechargeable batteries have a charge life of up to three years and can be recharged easily with the provided charger. It’s important to note that the rechargeable battery isn’t compatible with the older Swiffer Wetjet models, so if you do have an older model, you will need to purchase the AAA batteries.
What to do when your Swiffer WetJet stopped working?
If your Swiffer WetJet has stopped working, the first step is to unplug the unit and check the battery compartment. You should ensure the batteries are inserted correctly and replace any missing or damaged batteries.
If the batteries are in good condition, plug the unit back in and make sure it’s turned on. If you still don’t see any activity from the WetJet, try pressing the reset button on the battery compartment; this may kickstart the machine back into working condition.
If the WetJet still isn’t working, the next step is to check the water tank. Make sure the tank is filled up and the detergent reservoir isn’t empty. If you’ve recently switched detergents, the WetJet might need time to adjust.
Ensure the filters are clean, and if you have the instructions manual handy, consult that for instructions on how to properly clean them.
If the WetJet still isn’t working, it’s likely a mechanical or electrical issue and you’ll need to contact the manufacturer. Make sure you have the model and serial number ready when you contact customer support, as they’ll likely ask for this information.