Skip to Content

How do you install a Lyons contour tub?

Installing a Lyons contour tub is a relatively straightforward process, but some basic knowledge of plumbing and home renovation will be necessary. The following steps outline what is typically needed for a successful installation of the Lyons contour tub:

1. Begin by locating the area where you want to install the tub and measure the space accurately. If a wall is going to be used, mark the area to be cut out for the tub.

2. Cut out any necessary holes for plumbing connections, as directed in the instructions.

3. Install the drain and overflow assembly, following the directions provided in the tub documentation.

4. Install the tub into the opening, using a level and shims where necessary.

5. Connect the supply and drain lines to the water supply and drain respectively, using the appropriate connections provided by your local hardware store.

6. Connect the drain assembly to the overflow assembly, using plumber’s putty if needed.

7. Check all connections to ensure they are sealed properly and no leaks are present.

8. Turn on the water supply and check for any leaks. If any are present, you may need to tighten the connections or add additional putty.

9. Caulk around the outside of the tub and any joints between walls and the tub.

10. Fill the tub with water and test for leaks once again.

Once the tub is installed and free from any leaks, you can enjoy your new Lyons Contour Tub!

How do you install a bathtub surround direct to stud?

Installing a bathtub surround direct to stud involves several steps. First, locate and mark the studs in the walls where you will be attaching the surround. Drill pilot holes into the studs to make screwing them in easier.

Mark the desired height for the surround on the studs. Cut the studs to the appropriate height and attach the studs to the bathtub surround before mounting it to the wall. Place the surround into position and use a level to make sure it is even and secure it with screws.

Place backer board or plywood in the space between the bottom and back of the surround. Add caulking and grouting around the edges to seal the area and make sure the bathtub surround is attached securely.

Finally, install and secure the trim pieces using nails and caulk. Make sure to fill any holes or gaps in the trim pieces.

Does drywall go over the tub flange?

No, drywall should not go over a tub flange. The tub flange is an essential part of the bathtub installation and must be completely exposed and properly sealed. To ensure proper installation and function of the tub, the flange must be visible and accessible from inside of the enclosure.

The tub flange itself needs to be kept dry with a waterproof membrane such as cement-based waterproofing, such as RedGard, or with a self-adhesive membrane present around the flange. Once the waterproofing is installed, it can be covered with greenboard or a similar water resistant drywall, but not standard drywall.

What does direct to stud mean for a tub surround?

Direct to stud installation for a tub surround means that the wall panels of the surround are directly mounted to the wall studs, rather than to a backer board or other wall material. The benefit to this method of installation is that it enables for a more secure connection and a sturdier end product.

Additionally, it eliminates the need for spaces between the wallboard and the panels since the studs act as the spacers. Furthermore, direct to stud installation ensures that water won’t be trapped between the panels and wallboard which will help reduce the risk of mold.

This method of installation typically requires more tools and materials than other installation methods but the rewards of a sturdy, long-lasting tub surround are worth the additional effort.

When doing a direct to stud installation for a tub surround, it’s important to use a waterproofing material behind the panels to provide extra protection. Additionally, properly measuring and marking the studs and making sure all the screws are flush against the wall studs is essential for the stability of the tub surround.

Properly caulking the joints around the panels is also important to ensure there are no gaps that would allow moisture to seep in. Finally, make sure to properly seal the edges of the panels where they meet the wall studs to protect against water penetration.

Do you need cement board behind tub surround?

Cement board is a great way to protect your wall and tub surround. It can be used behind the tub surround to provide an extra layer of protection between the wall and the tiles. It also provides a structural backing, particularly important in wet areas such as the bathroom.

When installing cement board around the tub, it should go up to the same height as the surrounding tile, with a minimum of 1/8 inch backspacing. If the tile is not flush, use mesh fiberglass tape to fill in the gaps between the cementboard and the tiles.

Additionally, make sure to use thinset mortar and waterproof membranes to fully protect your wall and prevent moisture damage.

Do you put drywall over tub surround?

Yes, it is possible to put drywall over a tub surround, but it is not recommended for a variety of reasons. Hanging drywall over a tub surround can be complicated and difficult, since you will need to properly fit it around any curves and properly finish the edges and corners.

In addition, it can be difficult to create a watertight seal between the drywall and the tub surround, so regular maintenance and repair may be necessary over time in order to prevent water damage. Also, drywall can be quite heavy, so extra structural support may be necessary in order to ensure safety and stability.

For these reasons, it is generally recommended to use wallboard specifically designed for use in wet areas, such as moisture-resistant drywall or greenboard. These materials are designed to be more resistant to water and moisture, making them a better option for installations around your tub surround.

What is the easiest tub surround to install?

The easiest tub surround to install depends largely on the type of surround that is needed or desired. Generally, tub surrounds that come in a kit or are pre-assembled panels are the easiest to install because all that is required is cutting the panels to fit and using a few screws to secure them in place.

In addition, many DIY tub surrounds now come with adhesive backings to make the installation process even simpler. The adhesive backing eliminates the need for screws to hold the surround securely in place and allows for a quick and easy installation.

If a surround with a tile or stone finish is desired, it is generally easier to purchase large porcelain or ceramic wall panels that can be installed in much the same way as a prefabricated kit. If both cost and ease of installation are major factors, plastic or fiberglass tub surrounds are typically the most affordable and easiest to install.

Do you put cement board over tub flange?

Generally, it is not necessary to put cement board over a tub flange. Tub flanges are meant to provide a solid waterproof base for the tub installation and will not require cement board. However, there are some situations where it is recommended to install cement board over the flange.

If there is any evidence of water damage or intrusion from other sources around the flange area, cement board can provide an additional layer of protection. Also, if the flange is not firmly secured to the substructure, using cement board can provide additional support.

In either of these cases, it is recommended to use an appropriate tile underlayment over the cement board for improved water resistance before installing the tub.

Can you screw through tub flange?

Yes, you can screw through a tub flange. This is typically done when installing a new bathtub. A tub flange serves as the anchor for the tub and is typically made of steel or plastic and has two or three screw holes that allow you to screw it into the wall studs.

The screws help to support the weight of the bathtub and keep it in place. When installing the flange, it’s important to ensure that the screws are driven in properly and flush with the walls surrounding the tub.

In order to ensure that the screws won’t come loose over time, it’s best to use a stud finder and make sure you’re screwing into the studs of the wall. Once the tub is secured to the wall with the screws, it’s ready for installation.

Can you install shower surround to studs?

Yes, you can install a shower surround to studs. This can be done by attaching the shower surround panels to the studs using screws and anchors. You can also use adhesive to attach the panels to the studs.

Depending on the type of material used, you may need to use additional materials such as sealants and caulking to protect against moisture. Additionally, you may need to place waterproofing material such as a vapor barrier or backer board between the studs and the shower surround to protect against water leaking into the wall cavity.

It is also important to seal all seams and joints with silicone or other water resistant material in order to prevent water from entering the wall cavity.

How do you attach a fiberglass tub to a stud?

First, you need to measure and mark the wall of the tub at the places that the studs will go. Then use a drill to make small holes to use as a guide to ensure that your fasteners are placed correctly.

Next, find the studs in the wall by lightly tapping along the wall until you hear a slightly different sound. Then, use a stud finder to ensure that you have located the studs correctly. After you know where the studs are, you can use wall anchors to mark the wall so that it can support the weight of the fiberglass tub.

Once you have the openings for the studs marked, you can use drywall screws to attach the tub to the wall by screwing them through the hole and into the stud. Alternatively, you can use toggle bolts or molly bolts to secure the tub to the wall.

Make sure you space the screws correctly so that they are strong enough to hold the weight of the tub.

Finally, use caulk or grout to seal any gaps between the tub and the wall to help prevent water damage. Make sure that you don’t use too much caulk, as it can create a slippery surface and cause water damage over time.

Can you install direct to stud shower over drywall?

Yes, you can install a direct-to-stud shower over drywall. However, it requires that you use the proper materials and techniques so you can ensure the shower is structurally sound, waterproof, and able to handle the weight of the walls.

First, you will need to install thick, waterproof sheathing behind the drywall. This sheathing should be secured to the studs with corrosion-resistant screws. Next, you will need to install a waterproof membrane over the sheathing and seal it to the wall studs.

Finally, you will need to install drywall over the membrane and seal it with waterproof caulking. With these steps, you can ensure that your direct-to-stud shower over drywall is safe and durable.

Can you put any tub surround with any tub?

No, you cannot put any tub surround with any tub. The size, shape, and material of the tub and surround must be compatible in order for the installation to be successful. If a tub and surround are not made to go together, the tub surround may not fit correctly, water may leak, and it may not provide enough structural support.

Additionally, you must make sure the tub has the correct drain configuration to match the tub surround. When selecting a tub surround, be sure to measure both the tub and the wall to ensure the correct size of tub surround is chosen.

Additionally, review the manufacturer’s recommendations to determine the best materials to be paired together. It is important to follow their guidelines to ensure the proper installation of both the tub and the surround.

Does a tub surround go over drywall?

Yes, a tub surround can go over drywall. Before you install the surround, you should ensure that the underlying drywall is in good condition and free of any damage. If there are cracks or holes, you should patch them with drywall joint compound or spackle before you install the surround.

You should also ensure that the drywall is secured firmly to the wall studs and any loose areas should be securely fastened in place. Once the drywall is ready, you can cut the surround pieces to size and attach them to the wall.

Make sure to use an adhesive that is specifically designed for tub surrounds when installing the pieces; this will help ensure a tight seal and waterproof protection from moisture.

Is it hard to replace a tub surround?

Replacing a tub surround can be a relatively difficult process. Depending on the type of tub surround you need to replace, you may need to make some modifications to the existing walls or you may need to purchase and install a whole new unit.

If you don’t have a lot of experience with home improvements and plumbing, we strongly recommend hiring a professional. They will be able to assess the job and make sure that the necessary steps are taken to safely and successfully replace the tub surround.

When replacing a tub surround, you must also consider the number of steps or panels, the wall material, the size and configuration of the tub, the design of the surround, the accessories needed, and any other additional materials needed for your project.

Due to the complexity of the job, it is important to ensure that the tub surround is correctly measured before it is purchased and that the installation of the panels or steps is performed correctly and neatly.

Additionally, all of the connections should be checked to make sure that they are all secure and that the water is prevented from leaking. All of these steps combined can add up to a long and challenging process, so it is always recommended to get professional help if possible.