Installing a WingTite shower drain is simple and relatively quick. First, you need to shut off the water leading to the shower area, disconnect the existing drain, and then prepare the shower for the installation of the new WingTite drain.
To begin, start by covering the drain opening in the shower floor with a waterproof membrane. Ensure that it covers the entire opening and that it is properly secured. Next, slide the WingTite drain assembly into the drain opening.
Make sure that the rubber gasket is on the bottom of the drain assembly and the center section of the drain is sticking up.
Now insert the provided screws through the screws and into the drain, using a screwdriver or power drill. To ensure a proper, tight fit, make sure that these screws are screwed as tight as possible. Finally, connect the drain pipe to the back of the WingTite assembly, using the provided adapter and silicone sealant.
Once all connections are secure, turn the water back on and test for any leaks. If no leaks are present, the installation is complete. With a WingTite shower drain, you can now enjoy the peace of mind that the drain won’t loosen or get blocked with hair.
Do you glue shower drain to pipe?
No, you should not glue a shower drain to the pipe. The drain should be held in place by a set of screws (typically two or four) that attach the drain to the shower’s flange or flange support. Sufficient tightening of the screws should provide enough grip on the pipe to keep it in place.
If the drain is loose or keeps coming loose, use plumbers’ putty or an adhesive to create a better seal. However, you should take care not to use too much adhesive, as this may create an obstacle to proper draining.
Can I use silicone instead of plumbers putty on shower drain?
In most circumstances, no. Plumber’s putty is the most typical material used to seal the shower drain and should be preferred over silicone in most cases. Plumber’s putty seals over wide gaps easily and is non-hardening.
It also prevents wastewater and foreign material from damaging the finish and seal of the drain. On the other hand, silicone is much harder to use, as it cures quickly and is difficult to smooth without an expert’s hand.
Also, silicone can potentially react with some of the metals used in drainage systems. For a secure and long lasting seal, plumber’s putty is clearly the better option.
Should I grout or silicone around shower drain?
Whether you should grout or silicone around a shower drain depends on a few factors. If you are using a drain with a collar, a ring for securement, silicone is the best option to create a waterproof seal.
Show drains with these collars can be installed and sealed with silicone, making the job look professional.
If your shower has a no-caulk drain, and drain without a collar, you’ll want to seal it with grout or an epoxy-based sealant. You will want to avoid silicone in this case because a non-caulk drain is designed to accommodate movement.
Silicone is not the best choice for negotiating movement, so grout is ideal because it has more elasticity.
Before deciding what’s best for your application, it is recommended that you check with the manufacturer for any specific instructions and recommendations.
Where do you put the drain in a walk in shower?
When planning a walk in shower, you want to make sure that you plan for the drain placement. Most walk in showers require a large rectangular or square drain just inside the entrance of the shower. The drain should be connected to the main framed in shower pan with a trap, which is the PVC pipe connected to the drain that helps to keep water in the drain and prevents bad odors from entering the space.
When placing the drain inside the shower space, it should be in the center of the floor so the water will be evenly distributed while draining. In addition, make sure the drain is far enough away from walls and other objects so water can freely flow all the way to the drain.
When tiling the floor, make sure the drain is in the center of the pattern, but not directly under the shower head so it will not be coated with grout. Finally, pay special attention to any required height and size specifications for your shower’s drain so it will be compatible with the rest of your plumbing fixtures.
Does a linear drain have to go wall to wall?
No, a linear drain does not have to go wall to wall. Linear drains are not required to be placed between two walls, they can also be used adjacent to one wall, depending on the layout of the bathroom.
Linear drains can be placed anywhere along the circumference of a space. This is beneficial, as it offers more flexibility in planner and designer layout options, allowing them to more carefully plan and customize a space to best suit the needs and preferences of the user.
Where is the place to put a linear drain in the shower?
The best place to install a linear drain in a shower is at the lowest point of the shower floor; typically the corner. Linear drains are installed to facilitate the drainage of water in the shower, so it should not be placed in any area of the shower that is not level or at least not the lowest point.
It is typically placed near the edges of the shower, preferably in a corner. However, much of the placement is dependent on the size and shape of the shower, so you will need to consult a professional plumber or contractor for the final decision.
Additionally, when installing the drain, it is important to ensure there is sufficient slope between the shower floor and the drain for optimum drainage.
How tight should a shower drain nut be?
The shower drain nut should be tightened as much as possible by hand. If you have a wrench, you can use it to tighten the nut further but be careful not to over-tighten. Over-tightening the nut can strip the threads or damage the gasket of the seal, leading to seals or leaks developing around the drain.
If the nut is too tight, it can also cause the drain flange to warp or crack, which can also lead to issues. As a general rule of thumb, the nut should be tight enough to ensure the drain flange is level with the shower floor and the seal is properly secured, but not overly tight.
Why is there standing water in my shower drain?
One of the most likely causes is that the drain is clogged. Hair, soap scum, and other debris can accumulate in the drain and block the flow of water. This can cause standing water to accumulate in the shower.
In some cases, the drain may need to be fully or partially snaked in order to clear the blockage.
Another potential cause of standing water in the shower drain is a collapsed or broken pipe. If this is the case, you may need to have a professional plumber investigate the issue in order to properly repair or replace the affected pipe.
Finally, it is possible that the standing water may be due to a faulty drain trap. This is the bend in the drain line that is designed to stop sewer gas from entering the home. If the trap is not adequately sealed, it can allow water to back up into the drain.
If this is the case, it may be necessary to repair or replace the drain trap.
Are linear shower drains hard to clean?
No, linear shower drains are not particularly hard to clean. These modern drains are designed to effectively manage water while also keeping cleaning easy. Firstly, they have wide grates that allow dirt and debris to easily be collected and removed.
Secondly, the grates are often removable, allowing for more thorough cleaning. Lastly, the grates may be stainless steel or another material that does not easily corrode or rust, which makes regular maintenance easier compared to traditional shower drains.
Overall, linear shower drains are relatively simple to keep clean, making them a great choice for your home.
Does Drano work in a pipe with standing water?
Yes, Drano does work in pipes that have standing water. The thick gel formula of Drano is designed to cling to the pipes and dissolve the clog, even in water. When using Drano, please be sure to follow the package instructions carefully and take the necessary safety precautions.
In addition, it is important to only use the Drano in a pipe that is free of standing water. If the pipes contain standing water, it is necessary to first remove the water before using the Drano. Once the standing water has been removed, then Drano can be used to treat the clog.
Can you pour Drano through standing water?
No, it is not recommended to pour Drano through standing water. Drano is a corrosive chemical that can cause irritation if it comes into contact with skin or eyes, so it is important to be extremely careful when handling it.
Additionally, if the standing water contains any organic material, such as food scraps or grease, then pouring Drano into it will create a dangerous reaction that could create hazardous fumes. Furthermore, Drano should be used according to the instructions on the label, and most products intended for use in sinks should not be used with standing water.
Instead, it is better to use a plunger or other traditional drain cleaning methods to clear the blockage before pouring Drano into the drain.
Do linear drains get clogged with hair?
Yes, linear drains can get clogged with hair. Hair is one of the most common causes of clogged linear drains, due to its tendency to easily collect, stick to surfaces, and become tangled. Hair can quickly build up inside the drain line where it can cause significant blockages in the plumbing system.
In some cases, a clog made up of only a single strand of hair can be enough to trigger a blockage.
To prevent clogs, it is important to make sure that all drain strainers, plugs, and covers are regularly emptied or checked to ensure that hair and other debris are not collecting there. Also, using a drain cleaner every few weeks can help keep drains clear and reduce the risk of blockages.
In cases of serious clogs, a professional plumber can be called in to safely and efficiently remove the clog.
Does baking soda and vinegar really unclog drains?
Yes, baking soda and vinegar can be used to unclog drains. The combination of baking soda and vinegar creates a foamy reaction that can help to loosen and break any clogs in the drain. The reaction produces a gas which can help to push any debris out of the drain.
Additionally, the acidic nature of vinegar can help to dissolve organic material such as food particles, grease, soap residue and hair. To use baking soda and vinegar to unclog drains, mix 1/4 cup of baking soda with 1/4 cup of clean vinegar and pour it down the drain.
Allow it to sit for a few minutes before running hot water through the drain. This method can help reduce clogs in the pipes, however, it may not work for all blockages. For more stubborn clogs, a drain snake or professional plumber may be needed.
Will vinegar hurt drain pipes?
Vinegar can be effective in helping to clean out your drain pipes, however it should not be used to the exclusion of other methods or as a remedy for larger problems. In general, vinegar can help loosen a build-up of dirt, soap and grease in the pipes and can also help prevent clogs from forming.
However, over-use of vinegar can be damaging to some pipes, especially those made of metal due to its acidic nature. Therefore, it is recommended that vinegar be used only occasionally or in small amounts.
For more serious clogs, the services of a professional plumber should be sought in order to avoid any permanent damage to your pipes.