Lighting the pilot light on an Envirotemp water heater is a relatively simple process that starts off by shutting off the gas supply. Once the gas is shut off, the gas valve on the Envirotemp needs to be reset to the pilot position.
Push the red button in and hold it while simultaneously pushing the knob all the way in.
Next, the pilot light needs to be lit using a long match or stove lighter. Hold the ignition next to the control valve and press the red button. The pilot light will start to light. If the pilot light does not ignite, the gas has not been turned on yet and the knob will need to be adjusted.
Once the pilot light is lit, the gas should be slowly increased and the knob turned to ON. This will allow the pilot light to continuously stay lit. Make sure the flame isn’t too long and that the pilot light doesn’t seem to go out after a few minutes.
If so, you will need to go through the entire process again. Finally, make sure to turn the gas valve to OFF when you are finished.
Can I relight the pilot light by myself?
Yes, you can relight the pilot light by yourself, however it is important to take necessary safety precautions first. Before you attempt to relight the pilot light, it is important to make sure that the gas is turned off to the appliance at the gas shut-off valve.
You will also want to make sure the room is very well ventilated since carbon monoxide can be present when dealing with pilot lights and other gas appliances. To relight the pilot light, you will need a lighter or a long-stemmed match.
Once the gas is off and the room is sufficiently ventilated, locate the pilot light and find the small access panel near it. Open the access panel and look for a small knob usually with a red or blue color indicating the direction you should turn it.
You will need to turn the knob clockwise and hold it in the fully forward position until you hear the click of the gas valve that signals it is fully open. With the gas still off, you will then need to use your lighter or match to ignite the pilot light at the end of the long-stemmed gas tubing.
Due to the flow of gas and air, the pilot light should stay lit. If it does not, you will need to repeat the steps until it does. Once the pilot light is lit, you will then need to set the knob on the access panel back to the off position.
You should now test the appliance to make sure it is functioning correctly before using it.
How do you manually light a water heater pilot?
Manually lighting a water heater pilot is a fairly simple process that requires a few basic steps. First, you will need to turn off the power supply to the water heater. Then, locate the pilot light.
It should be found near the base of the water heater near the water line valves or gas connection. Once you’ve found the pilot light, inspect the area surrounding it for any potential hazards such as leaks or other debris.
If the area is clear, you can begin the lighting process.
To light the pilot light, use a long lighter or match and make sure that your hand is far enough away from the flame to avoid burning yourself. Turn the knob controlling the pilot light to the “pilot” setting and hold it down while you ignite the pilot light with the match or lighter.
Keep the knob held down for approximately 60 seconds and then release it. If the pilot light stays lit, the next step is to turn the knob to the “on” setting and allow the water heater to heat up.
If the pilot light does not stay lit when the knob is released, you may need to repeat the steps above. If the pilot light still does not stay lit after a few attempts, then you may need to call a professional for help.
Remember, when working with water heater pilot lights, always exercise caution and follow the manufacturer’s instructions closely.
Do you need to relight pilot on water heater?
Yes, you may need to relight the pilot on a water heater. The pilot light provides the heat source necessary to ignite the gas to heat the water in the tank. Depending on the type and model of water heater, there may be slightly different steps involved in relighting the pilot, but the basics are the same.
You’ll need to locate and locate the pilot compartment, locate and press the knob that is used to shut off the gas, locate the thermo-couple and pilot light assembly, press the knob to set it to the “Pilot” setting, press the knob to ignite the pilot light, and usually hold the knob in for about 30-60 seconds before releasing it.
Depending on your model, you may also have to turn the knob to the “On” setting before finishing up. It’s important to refer to your manufacturer’s instructions for the specific steps to relight the pilot light on your unit, as water heater models can vary significantly.
How long does it take the water to heat up after you relight a pilot light?
The amount of time it takes for the pilot light to heat up the water depends on several factors, including the type of water heater being used, the age of the water heater, the ambient temperature of the room, and the water temperature in the tank.
Generally speaking, the pilot light will take longer to heat up the water if the water is already cold. If the room is cold, it will take longer for the pilot light to warm up the water in the tank. If the water heater is new, it will take less time for the pilot light to heat up the water.
On average, it can take anywhere from 15 – 30 minutes for the pilot light to heat up the water.
How do I know if my pilot light is out?
You can check to see if your pilot light is out by first locating the furnace, then looking for the little metal or plastic window on the side of the furnace. Inside the window, you should be able to see a small light.
If the light is off, then your pilot light is out and needs to be relit. If the light is on but you can’t feel much heat coming from your furnace, it is likely that your pilot light has gone out as well.
In order to relight your pilot light, you must first find the appropriate shut off valve and turn it off. Once it is safely turned off, you can then locate the pilot light portal by consulting your furnace’s user manual.
If the pilot light portal isn’t easily found, you can always check the sides, back, or bottom of the furnace for an actuator that can be used to turn on the pilot light.
After the pilot light port has been found, you will then need to clean the area around the pilot light. This should be done with a vacuum cleaner to make sure all dust and debris has been removed. Once the area is clean, you will then need to locate the pilot light (which will most likely be a red or blue button) and hold it down while lighting the flame.
After the flame has been lit, you can then slowly release the button and the pilot light should remain lit. If the pilot light does not remain lit, you will need to repeat the process until it does.
What to do when pilot light won t light?
When the pilot light on a gas appliance won’t light, first determine whether it’s simply out or if there’s a bigger problem. If it’s simply out, relighting it using the valve and knobs is simple and only requires a lighter.
Start by turning off the gas and then rotating the knob counterclockwise to the “OFF” position. After that, wait five minutes before turning the main gas line back on (in order to reduce the amount of any residual gas in the system).
After that, turn the knob to the “PILOT” position and press the knob down. Now take your lighter and light the pilot light. After that, hold down the knob for 30 seconds then release it. The pilot light will now remain lit.
However, if the pilot light still does not light, it may be due to a more complex problem and you should consider contacting a professional for assistance.
How do I relight my electric pilot?
In order to relight your electric pilot, you’ll need to turn off the power that supplies electricity to the pilot light. You should also make sure that the gas line is securely shut off before relighting the pilot.
Once that is done, you should press down on the gas knob for a few seconds to make sure the gas line is really closed. After that, reset the switch of the pilot or circuit breaker and turn the power back on.
Now you can begin to relight the pilot. To do this, turn your gas knob counter-clockwise to the ‘light’ position. Push the manual reset button or pull the red toggle switch near the pilot to activate the spark.
This will light the pilot. Back the gas knob off to the off position and then turn it to the on position once again. The pilot should be lit.
Once the pilot is on, you should make sure the flame is in the right position and set the gas knob to the right position. This should be done by adjusting the knob clockwise. You should also check the thermostat to make sure it’s operating properly and adjust the flame level if necessary.
Finally, turn the power off and then back on again to reset the circuit breaker. With the power off, keep an eye on the pilot and make sure it stays lit. If the pilot light goes out during the reset, you’ll need to start the process over again.
Will heat work if pilot light is out?
No, the pilot light is a necessary component of many heating systems that allow heat to be generated. Without a flame from the pilot light, the heat will not work and your home will not receive the appropriate warmth.
To reignite the pilot light, you must first turn off the gas valve and find the pilot light access. Once you have located the access panel you will then need to follow your manufacturer’s instructions to ignite the pilot light.
If you lack access to the manufacturer’s instructions, relighting a pilot light may involve turning the gas back on and using an extended lighter or match to ignite the flame. Following the successful relighting of the pilot light, give the furnace time to heat up before testing the system.
If this does not resolve the issue, you may need to contact a professional for help.
Is it an emergency if the pilot light goes out?
It depends on the type of appliance you are referring to. If you mean the pilot light of a gas stove, it is not necessarily an emergency, though it will prevent the stove from working properly until the pilot light is re-lit.
If your pilot light has gone out, you should turn off the gas valve to prevent a potential gas leak and contact a qualified professional to re-light the pilot light.
On the other hand, if you are referring to the pilot light of a gas-powered heating system, this may be more serious and require immediate attention. A gas-powered heating system relies on the pilot light to detect if the flue is working properly.
Therefore, if the pilot light goes out, it indicates a possible issue with the flue, which is a serious safety concern. In this case, you should turn the gas valve off, open windows to disperse any gas that has accumulated, and contact a professional immediately.
Can you manually light a pilot light?
Yes, you can manually light a pilot light. It is a fairly straightforward process, though you should keep in mind that different appliances may have slightly different instructions. Generally, the process involves locating the pilot light, turning off the gas valve, pressing down on the reset button, and holding a lit match or lighter to the pilot light.
Once the pilot light is lit, you can turn the gas valve back on and you should be all set. Make sure you follow the manufacturer’s instructions exactly and ensure that the area is well ventilated when you are lighting the pilot light.
Additionally, depending on the appliance, you may need to hold down the reset button for a few seconds after it has been lit.
Will the gas company light my pilot?
No, the gas company will not light your pilot. While you may be able to contact the gas company and have them inspect and assess your pilot light, they will not light it for you. It is ultimately your responsibility as a homeowner to light your pilot light.
In most cases, the instructions to light your pilot light can be found on the appliance, but you may need to consult your owner’s manual if the instructions are not readily available. In the event that you are feeling uneasy about lighting it by yourself, you should contact a professional technician who can properly light your pilot light.
Is it safe to light your pilot light?
Yes, it is safe to light your pilot light. However, when doing so it is important to use caution to avoid injury or property damage due to gas leaks, fires, or explosions. Make sure the gas valve is firmly in the “off” position before proceeding to light the pilot light.
It is also important to follow all safety instructions found in the appliance’s owner’s manual when lighting the pilot light. Additionally, if the appliance has an electronic ignition system, it is recommended to contact a qualified service technician for assistance.
Furthermore, if the pilot light won’t stay lit, it may be a sign of improper ventilation, a broken thermocouple, an improperly adjusted pilot, or an impure fuel source. In these cases, it is best to leave repairs to a licensed professional to avoid any potential hazards.
Do pilot lights give off carbon monoxide?
No, pilot lights do not give off carbon monoxide. Pilot lights generally use a small flame to ignite the gas for the appliance or device. The primary purpose of the pilot light is to create the small, consistent flame needed to quickly start and maintain a larger gas flame when turned to the “on” position.
Pilot lights, like other gas and oil flame sources, are potentially capable of producing carbon monoxide. However, if they are working correctly and have been maintained properly with an annual inspection, they do not produce carbon monoxide.
In fact, today’s modern ignition sources, including pilot lights and electronic ignitions, are more reliable and less prone to producing carbon monoxide than the continuous standing pilot lights of the past.
What happens if pilot light goes out on gas furnace?
If the pilot light goes out on your gas furnace, then the furnace will not be able to heat your home. This can be a major inconvenience during the cold winter months. Immediately check to see whether the pilot light remains lit.
If the pilot light has indeed gone out, the first step is to make sure that the gas valve is in the “on” position. If it is in the “on” position, then you need to light the pilot light with a match or lighter.
There should be an access panel on the furnace which enables you to reach the pilot light. To light the pilot light, make sure that the valve is in the “off” position, depress the reset button, hold a lit match or lighter near the pilot light and turn the valve to the “on” position.
If the pilot light fails to light, there could be an issue with the gas valve, the thermocouple, the pilot tubing, or the gas control valve. In this situation, it is likely best to contact a professional HVAC technician to fix the issue.