To measure the toilet flange, you need to start by taking three measurements: the rough-in measurements of the flange, the diameter of the waste pipe, and the distance from the wall to the flange. The rough-in measurement is the distance from the finished wall to the center of the toilet flange’s mounting bolts.
Measure from the center point of the drain pipe itself in order to make sure you get an accurate measurement. The diameter of the waste pipe should also be measured, with the most common sizes being either 3-inch or 4-inch pipes.
And lastly, measure the distance from the wall to the flange. This will tell you how much space the flange will need in order to fit properly.
Once the measurements are taken, the next step is to determine the correct size toilet flange to purchase. The most common toilet flange sizes are 3-inch and 4-inch, with 4-inch being the most common size.
The 3-inch toilet flange is usually used with a 3-inch waste pipe, while a 4-inch will fit a 4-inch pipe. Once you have determined the correct size, you need to measure the width of the flange along the outside diameter and the height of the flange from the base to the lip, as well as the center of the pipe.
All three measurements will help you ensure that the toilet flange you choose will fit the drain pipe you are using.
How do I know if my toilet is 10 or 12?
In order to determine whether your toilet is a 10 or 12 inch model, it is important to measure the length of your toilet. You can measure the length of your toilet in two ways.
The first way is to measure from the wall behind the toilet, to the center of the drain hole. If the measurement is 10 inches, then your toilet is a 10 inch model. If the measurement is 12 inches, then your toilet is a 12 inch model.
The second way to measure your toilet is to measure the length of the bowl itself. You need to measure from the very front of the bowl, along the curved sides, to the back. If the measurement is 16 1/4 inches, then your toilet is a 10 inch model.
If the measurement is 18 1/4 inches, then your toilet is a 12 inch model.
Once you have measured your toilet, you will know for sure whether it is a 10 or 12 inch model.
Does a toilet flange go flush with tile or on top?
The installation of a toilet flange requires that it is mounted correctly. Typically, the toilet flange should sit slightly above the finished floor surface with a wax gasket to get a good seal. In some cases, the porcelain of the completed tile floor may reach up to, or even be slightly higher than, the level of the finished floor.
In these cases, the toilet flange should sit flush with the tile. If the tile is significantly higher than the finished floor surface, then the toilet flange should be set higher to ensure that the porcelain of the toilet bowl does not hinder the water seal.
It is important to not have the toilet flange installed either too high or too low. If the toilet flange is too high, it can cause the toilet to rock and impair its water seal. If the toilet flange is too low, the wax seal may be compromised.
Is it OK for toilet flange to be lower than floor?
Yes, in some cases it is acceptable for the toilet flange to be lower than the floor. This is typically recommended when the new floor is being installed over an existing concrete slab and the flange is below the height of the new subfloor.
This can help to make sure that the toilet is secure and level when it is installed. It is also acceptable to add a spacer to raise the toilet flange if needed. Generally speaking, it is best to ensure the toilet flange is as close to level with the floor as possible, as this helps secure the toilet and prevent it from leaking.
How many inches should a toilet flange be from the wall?
The distance of a toilet flange from the wall, or the distance between the finished wall surface and the center of the toilet flange, should generally be 12 inches. This 12-inch distance gives enough clearance to ensure that the toilet is able to be properly secured to the flange and that any wax rings used to seal the toilet to the flange can be installed correctly.
For installation in tight spaces, such as in a remodel or partial replacement of a toilet, a reduced flange protrusion is sometimes allowed, but it is not the ideal and is not recommended in all cases.
As a general rule, when possible, 12 inches should be the minimum distance from the wall and the center of the toilet flange.
Does a toilet flange go inside or outside the drain pipe?
A toilet flange is a fitting installed onto or into the floor that secures the base of the toilet and connects to the drain pipe. The toilet flange typically fits around the outside of the drain pipe in the floor.
However, some models, such as a resetable flange, can be fit inside the drain pipe. It is important to choose the right flange, as the measurements and size of the flange need to match the drain pipe for proper installation and operation.
Furthermore, depending on the type of piping being used, you may need to purchase a wax ring or other sealant to ensure a watertight seal between the base of the toilet and the flange. It is also important to ensure that the flange is level before attaching the toilet, to avoid any leaking issues.
Does toilet flange have to be perfectly level?
The answer is yes, toilet flanges do need to be perfectly level, as this is important for the proper functioning of the toilet. The flange sits at the bottom of the toilet bowl, and provides a solid and secure connection between the toilet and the drain pipe.
It creates a watertight seal that allows the toilet to hold back water as it fills. If the flange is not completely level, it could cause the toilet to leak or run. This can lead to costly repairs and water damage in your home.
For this reason, it is important to ensure your flange is level before you install your toilet.
Are all toilets 12 inches from wall?
No, not all toilets are 12 inches from the wall. The standard distance from the wall to the toilet is 12 inches in the US, but due to ever-changing building codes, this may not always be the case. In fact, some toilets will be closer to 10 inches or even 8 inches, depending on the room’s overall construction.
Furthermore, many wall-mounted toilets are mounted much closer to the wall and vary between six and eight inches, depending on model and size. To ensure that your toilet is installed correctly, it’s best to consult a building professional who can provide accurate measurements for the room.
Is my toilet a 2 inch or 3 inch?
The size of your toilet depends on the type and model you have. Generally, toilets come in either a 2 inch or 3 inch flushing system. To determine the size of your toilet, you need to look for the size stamped on the tank lid or on the flush valve located at the bottom of the tank.
Usually, it will be a 2 or a 3 indicating the size of the flush valve. If you don’t see these numbers, you may need to measure the diameter of the flush valve with a ruler. A 2 inch flush valve will measure approximately 2 3/8 inches, while a 3 inch flush valve will measure approximately 3 1/4 inches.
If you still have trouble determining the size of your toilet, you can contact the manufacturer for further help.
Can you replace a 11 inch rough-in toilet with a 12 inch rough-in toilet?
Yes, you can replace a 11 inch rough-in toilet with a 12 inch rough-in toilet. However, you will need to purchase a longer rear outlet toilet that is specifically designed for a 12 inch rough-in. This is because a standard 11 inch toilet base will not fit properly on a 12 inch rough-in closet flange.
To determine the specific measurements for the toilet that you should be purchasing for your 12 inch rough-in, please consult the manual for your specific model of toilet. Additionally, you may need to make adjustments to the existing installation of your current 11 inch rough-in toilet to accommodate the new 12 inch rough-in toilet, such as making sure that the new closet flange is securely fixed to the floor and that the new wax ring is properly sealed.
If you are unsure of the installation and replacement process, it is best to consult a professional plumber who can ensure the job is done correctly.
Should toilet flange be even with tile?
It depends on the style of toilet flange you have. If you have an “offset” flange, it should protrude about an inch above the floor, but it should be flush with the tile. If you have a wax ring style flange, it should be even with the tile.
Additionally, make sure the flange is level or slightly higher in the back so that the toilet can tilt slightly forward – this helps ensure a good seal between the toilet and the floor. When installing a new toilet, it is imperative to make sure the flange is properly installed and level with the tile so that the toilet can be securely fastened.
Do you have to screw the toilet flange to concrete floor?
The answer is yes, you should screw the toilet flange to the concrete floor if it is installed on a concrete slab. This is because without proper attachment, the toilet flange can move when you sit down and cause a water leak.
Additionally, a loose toilet flange can cause rocking and unevenness on the floor and can cause damage to the wax seal.
To install the toilet flange, you should first center the flange over the hole in the floor and then drill screws into the concrete at an angle. Make sure to countersink the screw head so that it is level with the floor surface.
You should use at least four screws to secure the toilet flange and make sure to use tapcon or masonry screws. Additionally, you should use a strong adhesive caulk to further secure the flange to the concrete and make sure to caulk both the base and the flange itself.
Do all toilets fit the same flange?
No, toilets do not all fit the same flange. The flange size will depend on the size and shape of your pipes, as well as the type of toilet you are using. Most toilets are either a 10” or 12” Rough-in, which refer to the distance from the wall to the center of the drain.
When selecting a toilet flange, you will want to make sure it is the correct size and shape for the type of toilet you are using. You may also need to consider the type of piping you are using and ensure that you select the flange that is made for that piping material.
Additionally, if you have a 4” pipe, you’ll need to use a 4” flange, not an 8” or 10” flange. Some toilets also require a wax ring, so you may need to purchase this wax ring separately.
Are all toilet flanges the same size?
No, toilet flanges come in a variety of sizes. The most common size for toilet flanges is 3” and 4”, but there are flanges that come in other sizes as well. If you are replacing an existing toilet flange, you should be sure to measure the size of your current flange to determine the correct size to buy.
Additionally, if you are installing a new toilet, the size of the flange should be determined by the style of the toilet you select. Toilet styles are designed to fit certain sizes of flanges, so be sure to check your toilet’s specifications before selecting a flange size.
Can you put a new toilet flange over an old one?
Yes, it is possible to put a new toilet flange over an old one. However, the process can be slightly more complex than just replacing one. To ensure a proper installation, you will need to assess the area to make sure that the flange is properly supported and that there is no damage to the existing toilet flange.
If the old flange is in good condition, you can remove it and clean the area so the new flange can be properly mounted. Then, use a sealant to ensure a tight fit between the new flange and the floor.
Make sure to connect the new bolts and tighten them securely before replacing the toilet. Finally, check the sealant and bolts once more before attempting to use the toilet. Proper care and maintenance when installing a new flange should provide long-lasting results.