Skip to Content

How do you push a bathtub drain?

Pushing a bathtub drain involves a few steps.

First, you want to make sure that the drain plug is securely in place and make sure you have the proper tools. You will need a wrench (either channel or pipe wrench), an adjustable wrench, a screwdriver and some pliers.

Once everything is ready, you should remove the drain plug. It may have a knurled head or a cross-head. Use the right tool to unscrew the plug. Once you’ve got it out, you should check the drain trap for any debris which may have become lodged in there, and remove it if necessary.

Next, you will need to remove the nut that holds the bathtub drain in place. Insert the adjustable wrench beneath the edge of the drain, wedge it up underneath and remove the nut.

At this point, you may need to use the pliers or screwdriver to remove the screw, if there is one, which is holding the drain in place.

Now, you need to push the drain down from the base of the bathtub. You can use the wrench, channel or pipe, to do this. Insert the jaws of the wrench underneath the lip of the drain and push it down.

Make sure you’re pushing in the same direction as the drain seal.

Once the drain is in place, you can refit and secure the nut, screw and plug. Make sure everything is tight so the drain isn’t loose and that the plug is properly seated.

Finally, ensure that the water is properly draining out of the bathtub when you remove the plug. If this is not happening, you may need to repeat the above steps, check the seal and make sure nothing is blocking the drain.

Congratulations, you have successfully pushed a bathtub drain!

What is the most effective way to drain the bathtub?

The most effective way to drain a bathtub is by locating the drain stopper in the tub, which is often located near the faucet and knob, and removing it. The drain stopper is typically a round plug, which can be unscrewed or pulled up to open the drain.

Once the stopper is removed, the bathtub should begin to drain. It can be helpful to slightly tilt the stopper both right and left to ensure that it is fully removed and the drain is open. Additionally, you may need to use a pair of pliers or a specialized tool to remove the stopper.

Once the stopper is removed, you can use a wet vacuum to help the water drain faster. After the bathtub has been drained, confirm that the stopper is clear of debris and can be securely fastened back into place.

Why can’t i snake my bathtub drain?

Unfortunately, the process of snaking a bathtub drain can be difficult and complex. Depending on the type of drain you have, there may be multiple bends, curves, and other obstructions on the way to the blockage.

The snake tool that is typically used for this job is made for straight drains and is not easily maneuverable within the complicated piping system of most bathtubs. Additionally, it can be difficult to find the access point for your bathtub drain, which is often hidden beneath the bathroom floor or behind a wall.

In some cases, a plunger may be used to unclog a bathtub drain, but this can only provide temporary relief at best. The plunger must be used with extraordinary care, as it might push the obstruction further down the drain and make the problem worse.

Even with the right tools, trying to DIY this type of plumbing job can be messy, time-consuming, and may not provide lasting results.

For these reasons, it is often best to contact a professional plumber for advice and assistance. They will have the right tools, experience, and knowledge to safely and efficiently diagnose and repair the issue with your bathtub drain.

How do you fix a deep clogged bathtub?

The first step to fixing a deep clogged bathtub is to determine the cause of the clog. Nine times out of ten, clogged bathtubs are the result of a buildup of hair, soap scum, and other materials. To remove the clog, there are a few options.

For a mild clog, you can use a commercial drain cleaner. Be sure to wear gloves and read the instructions carefully. If the clog is more serious, it may require specialized tools to break it up.

For a deep clog, you may need an auger, also known as a plumbing snake. An auger is a long, flexible rod with a corkscrew-shaped end. It is designed to break up tough blockages that are too deep to be reached with a plunger or commercial drain cleaner.

To use an auger, you will need to place it down the drain and turn it until it obtains a purchase into the clog. Then, draw it out, bringing the clog along with it. If the clog is not completely removed, you can repeat this process a few times until it is gone.

If the clog persists, you may need to call a professional plumber. While it is possible that the clog is due to a problem with your piping, it is far more likely that it is due to a buildup of debris that can be broken up or removed with the correct tools and materials.

Will pouring boiling water down a drain unclog it?

No, pouring boiling water down a drain will not unclog it. Boiling water is effective in some cases to help break up small amounts of grease or soap scum buildup that may lead to a clogged drain, but it is not a surefire way to unclog a drain.

In most cases, clogs require the use of a plunger or a professional-grade drain cleaning solution. Additionally, using boiling water on an already clogged drain can cause the trapped debris to move further down the pipe and become even more difficult to remove.

Can snaking a drain make it worse?

Yes, snaking a drain can make it worse. Snaking is designed to break up clogs, but the auger can cause damage to the interior of the pipes, especially if it is too big for the line. A snake often pushes the buildup further down, clogging up a different area.

This can also damage the pipes, potentially leading to a burst pipe or other plumbing damage. Depending on the complexity of the issue, snaking may be the best option, but it is important to consider the risk of damaging the pipes.

Calling a professional who can assess the situation is often the safest option.

What happens if snaking a drain doesn’t work?

If snaking a drain doesn’t work, it may indicate one of a few underlying issues. Clogs can be caused by a buildup of grease, hair, soap, or foreign objects that are lodged in a pipe. If snaking the drain doesn’t clear out the clog, the pipe may be blocked with a more substantial obstruction.

In cases like this, a professional plumber may need to be called to identify and address the issue. A plumber may use a high-pressure water jet to break up and flush out clogs. They may also deploy a camera to take a look inside the pipes, locate the obstruction, and determine what is causing the blockage.

In some cases, a broken, cracked, or blocked pipe may need to be repaired or replaced. These types of issues can be difficult to fix and require a qualified plumbing technician.

Once the obstruction has been cleared out, you can use a natural cleaner such as baking soda and vinegar to flush out any residue that remains in the pipes. This should help to keep the pipes clear in the future.

What causes a bathtub to not drain?

A bathtub not being able to drain can be caused by a variety of problems. The most common causes are a clogged or partially blocked drain or a faulty mechanical part like the stopper, P-trap, or drain pipe.

A clog in the bathtub’s drain could be caused by a number of factors such as hair, soap, oil, and other debris. The clog could also be caused by a buildup of minerals, such as calcium and lime, which is referred to as “hard water”.

If the problem is due to a faulty mechanical part, it would be necessary to replace the parts or repair the existing parts. In some cases, the problem may be more complicated and require more extensive investigation and repairs.

It is important to determine the source of the blockage before attempting to fix the issue. If you have any doubts or are unsure of how to address the problem, it is best to seek professional help.

Can you pour Drano into a tub with standing water?

No, you should not pour Drano into a tub with standing water. Drano contains sodium hydroxide and aluminum shards, which can be dangerous when mixed with water. It is also important to note that Drano should not be used in clogged tubs that contain standing water.

It can cause potentially dangerous reactions with the clogs, such as creating hazardous fumes or corroding pipes. Instead, if you have a clogged tub, you should use a plunger or a drain snake to remove the clog.

If these methods don’t work, you may want to call a professional plumber to safely clear the clog.

Why is there standing water in my bathtub drain?

Standing water in a bathtub drain is usually caused by a plumbing issue in your home. It could be due to a clog caused by hair, soap, dirt or other debris that has built up in the drain line. It could also be due to a plumbing vent that is blocked or malfunctioning, or a clog in the sewer line which is preventing water from draining out of the tub.

If water is standing in the bathtub drain, it’s a good idea to have a plumber come out and inspect the system to identify any problem and make repairs that are necessary.

How do you unclog a bathtub drain full of your hair without a snake?

Unclogging a bathtub drain that’s full of hair can be a tricky task, particularly if you don’t have a snake. However, there are a few proven methods that you can use to get your tub draining properly again.

The first method is to use a heavy-duty drain auger, also known as a cobra-style plunger. To use this, you’ll need an electric drill, a flexible hand snake, and a drain auger attachment. Place the auger attachment near the end of the hand snake, and secure it with duct tape.

Begin by drilling the auger into the clogged drain until it begins to make contact with whatever is blocking the drain. As you pull the hand snake back out, it should break up and remove any hair or grime that’s clogging the drain.

Another method is to use basic household items to break up the clog. Try combining ½ cup of baking soda with 1 cup of white vinegar and pour it down the drain. This should create a fizzing reaction that will help break down any debris blocking the drain.

Once the reaction quiets down, run hot water down the drain to flush out any remaining debris.

If neither of these methods work, you can also try using a chemical drain cleaner such as Liquid Plumr to break down the debris. First, remove any debris from the tub then pour the cleaner into the drain.

Follow the instructions on the bottle and let the cleaner sit for at least 30 minutes. This should help break up the clog and allow the water to drain freely.

No matter which method you choose, try to work slowly and carefully to avoid damaging the drain. If the clog still isn’t cleared after trying these methods, it’s likely that you have a major blockage and a professional plumber may be needed to resolve the problem.

How do you get the white part off the inside of a push in tub drain?

To remove the white part of a push in tub drain, you will need to use a pair of pliers and some penetrating oil or another type of lubricant. You will first need to remove the stopper or hair trap from the drain.

Then use the pliers to unscrew the drain ring that is beneath the drain. This can be difficult if the ring is stuck, in which case using the penetrating oil can be helpful. Once the ring is off, you can pull the drain up, revealing the white underside.

Now use the pliers to unscrew the white part from the tub. Once removed, it can be cleaned and replaced with a new one, if necessary.

Do pop up drains get clogged?

Yes, pop up drains do get clogged, just like any other type of drain. There are various things that can cause a pop up drain to become clogged, including hair, soap scum, food particles, and other debris.

If the pop up drain is clogged, a plunger or chemical drain cleaner can help unclog the drain. If the clog is too severe, it is best to contact a professional plumber to remove the clog and help prevent similar clogs in the future.

What will dissolve a blocked drain?

Chemical drain cleaners can be a very effective means of unblocking a drain. These drain cleaners use powerful chemicals such as sulfuric acid, sodium hydroxide, and lye to dissolve clogs and debris.

When used properly, these drain cleaners can be very effective in clearing out a blocked drain. However, you should always exercise caution when handling these products as they can be hazardous if handled improperly.

Always read the directions on the label carefully and wear protective clothing such as chemical-resistant gloves and safety glasses when handling them. Additionally, it is best to avoid using these products on plastic pipes as the chemicals can cause damage to the material.

Using a drain snake is another effective way of unclogging a blocked drain. A drain snake is a long, flexible piece of wire that can be inserted into the drain and pulled around and/or up and down to break apart clogs.

Small steel or plastic accessories can be attached at the end of the wire, which can be used help dissolve clogs. This method can be very effective in unblocking a drain, but some level of skill is required to use a drain snake effectively.

Finally, boiling hot water can be used to break down a blockage in a drain. You should always exercise caution when attempting this method as the hot water can cause damage to the pipes. Pour the boiling water slowly into the drain and leave for 5-10 minutes before running more hot water through it.

This method can be effective at breaking down soap scum and/or small, trapped particles. For larger blockages, you may need to repeat the process several times.

What’s the strongest thing to unclog a drain?

Using a plunger is often the most effective way to unclog a drain, as it creates suction to dislodge any clogs. For sink and shower drains, it’s best to use a cup plunger with a collar that fits into the drain.

To use a plunger, begin by creating a seal at the top of the drain with the plunger. Then plunge vigorously several times. The suction from the plunger should be strong enough to dislodge the clog. A second option is to use a drain snake, which is a long flexible metal cable with a manual or drill-powered crank.

Snakes can reach quite deep and can be used with a variety of attachments depending on the clog. Finally, if these methods don’t work you can try a combination of the two—first plunge the drain, then use a snake.

It might take repetition, but the combination will usually work to loosen and remove the clog.