Skip to Content

How do you remove a toilet flange that has been glued?

Removing a toilet flange that has been glued requires more work than a standard installation. Here are the steps to follow:

1. Start by turning off the water supply to the toilet.

2. Disconnect the water line, if present.

3. Unscrew the two bolts, which secure the toilet to the floor.

4. You should then be able to easily lift the toilet off the flange and out of the way.

5. The flange will be glued to the floor, so you need to use a reciprocating saw to cut through the flange and into the tile or whatever kind of floor you have.

6. Carefully cut as close as possible to the bottom of the flange, just around the outside edge and close to the floor.

7. Once the cuts are made, use a flat-blade screwdriver to pry up the edges of the flange piece and peel it away.

8. After the flange is removed, use a putty knife and some mineral spirits to clean the neighbouring area, removing any remaining adhesive or glue.

9. Finally, install a replacement flange using new gaskets and secure it to the floor with new screws.

Does the toilet flange get glued to the pipe?

Yes, the toilet flange should be glued to the pipe. To do this, you will buy a solvent-weld toilet flange and pipe cement. First, make sure that the flange and pipe are clean, dry and free from any dirt or dust.

You should then spread a thin layer of cement or primer all around the pipe, ensuring it reaches every part of the pipe’s surface. Once applied, you should insert the flange into the pipe and twist it slightly until the primer is worked into the joint.

Finally, you should apply more of the cement to the outside of the pipe and the flange and twist until the cement starts to form a seal. Allow the flange to dry and your installation should be complete.

Are PVC toilet flanges glued?

Yes, PVC toilet flanges are glued. The PVC flange connects the toilet to the drain line and fits inside the drainpipe. The flange must be sealed and secured to prevent the toilet from wobbling or leaking.

PVC flanges are glued using solvent-welding cement. This cement is specially designed to create a secure bond between the plastic materials in the flange and drain line. Applying the right amount of cement to both surfaces, and allowing for complete curing, is essential for a secure seal.

Once all of the surfaces are properly sealed, the toilet is seated onto the flange, and the nut and bolt combination is used to secure the toilet firmly in place.

Should you caulk around a toilet flange?

Yes, you should caulk around a toilet flange for a number of reasons. Caulking helps to create an airtight seal around the toilet flange, which helps to prevent the growth of mold and mildew. Without the caulk, there can be a lot of exposed surfaces where moisture can accumulate, leading to the growth of mold and mildew.

The caulk also helps to prevent the flange itself from corroding or rusting over time, helping to prolong its lifespan. Additionally, caulk can help to reduce the potential for water or sewage to leak into or out of the area surrounding the toilet flange, helping to prevent extensive water damage in your home or potential sanitary issues.

How do you stop a glued PVC joint from leaking?

To stop a glued PVC joint from leaking, there are a few steps to follow. First, it is important to make sure the joint is properly installed and has been glued correctly. Make sure the pipe is cut cleanly and that the bell of the pipe is properly seated in the socket.

Next, the joint needs to be dry-fitted with all the appropriate parts – a sleeve, a gasket and any connectors. Apply a generous amount of primer to the inside of the joint, allowing it to penetrate the surface for a few minutes before moving on to the next step.

Once the primer has fully dried, use PVC cement to glue the pipe and fittings into place. Finally, give the joint a quick press to ensure a tight seal and hold it in place until the glue has completely dried.

With these steps followed, the joint should be secure and no longer leak.

Is PVC glue permanent?

Yes, PVC glue is a permanent adhesive and forms a strong, lasting bond. When applied to two PVC surfaces, the glue sets in as little as 30 minutes, creating a bond that is stronger than the PVC itself.

PVC glue is resistant to humidity and water, and remains flexible in a variety of temperatures, making it an ideal choice for many applications. The durable bond is great for indoor and outdoor applications, making it a popular choice for securing various types of PVC projects.

PVC glue can also be used on rubber and plastic materials, making it a very versatile and reliable product.

Will PVC glue hold water pressure?

PVC glue is specifically designed for assembling PVC pipes and it will certainly hold water pressure, as long as the pipes have been properly connected. PVC adhesive is incredibly strong and provides you with a watertight joint that won’t leak or corrode.

It is recommended to always use PVC glue when working with PVC pipes to ensure a strong, lasting connection. It is important to ensure that the joint area is completely clean and that the glue is spread evenly between the two pipes, as any gaps or air bubbles will compromise the seal.

Once assembled, the PVC glue should be left to dry for several hours to make sure the joint is secure. This will ensure the connection is able to hold water pressure safely and securely.

Can you break the seal of PVC glue?

No, it is not possible to break the seal of PVC glue. PVC glue is a permanent adhesive and once it is applied and dried, it forms a strong bond that cannot be reversed. It is designed to provide a permanent hold and it will not become brittle or break away.

Therefore, once the seal of PVC glue is applied and dried, it cannot be broken.

What kind of glue to use on PVC toilet flange?

When it comes to choosing the right kind of glue for a PVC toilet flange the most important thing is to make sure you choose one that is both safe and effective. Generally, the best type of glue to use on PVC toilet flanges is a PVC cement, such as one that’s specifically made to work with plastic plumbing like Orbit PVC Cement Glue.

This type of cement is specially formulated to bond rigid PVC pipes and will dry quickly to form a permanent joint. Make sure that the cement is designed for plumbing, as opposed to other types of cement designed for fixing PVC furniture and similar items.

Additionally, it’s important to read and follow the instructions and safety warnings that come with the product.

Does a toilet flange need to be screwed to the floor?

Yes, it is important to secure a toilet flange to the floor in order to ensure a successful installation. The toilet flange is a key component of the toilet installation and is the part that attaches the toilet to the drain pipe in the floor.

Such as using mounting bolts, using epoxy caulk, or using a combination of both. Mounting bolts are typically used when the flange is on a concrete subfloor, while epoxy caulk is often used when the flange is on wooden or sealed floor.

No matter which method is chosen, it is important to make sure the flange is securely fastened to the floor in order to prevent leaks and future problems.

Can you put a new toilet flange over an old one?

Yes, it is possible to put a new toilet flange over an old one. The first step is to determine if the existing flange is properly seated against the floor. If the existing flange is raised and not flush with the floor, you may need to remove it and install a new flange in its place.

Using a drill and concrete bit, you can make holes in the old flange. Remove the screws while wearing safety glasses and remove any old sealant or putty that may remain. Next, you need to thoroughly clean the underside of the flange and the area surrounding it, as well as the floor, so that the new flange is able to adhere to the floor properly.

Place the new toilet flange over the existing flange and make sure that you have putty on the underside to ensure a water seal. Check that the flange is level, secure it into place with concrete screws.

Finally, use plumber’s putty around the base of the toilet and screw it into the flange.

Does toilet flange sit on concrete or tile?

The toilet flange sits on the floor, either on top of the concrete subflooring or the installed tiles. The toilet flange is used to secure the base of the toilet to the floor, connecting the two pieces and creating a watertight seal.

The area that the toilet flange will typically be installed in is typically either concrete or tiled.

In most bathroom settings, the flange would be installed on a tiled floor as the tile is easier to level and provides an aesthetically pleasing look. When installing the toilet flange, the installer will need to check for the thickness of the tile floor prior to installation.

If the tile is thicker than 1/4-inch, a toggle flange must be used in order to properly secure the base of the toilet.

If the area of the bathroom is a concrete subfloor, the installation process for the toilet flange is far simpler. As long as the floor is level, the flange is relatively easy to install, as the flange design allows for it to be screwed directly into the concrete.

Specific types of screws can be used, depending on the type of flange being installed, so ensure that you are using the correct type of screw for the installation.

Does toilet flange have to be perfectly level?

Generally speaking, yes, the toilet flange should be perfectly level. A toilet flange is the plastic or metal fitting that attaches to the waste line beneath the toilet and connects to the drainpipe in the floor.

It is also the part of the toilet that the bolts secure the toilet to the floor. If the flange is not level, there is an increased risk of water leakage, which can lead to costly damage to your home’s flooring or subflooring.

Installing a toilet flange is a fairly simple job that can be done in a few steps with the right tools and materials. Start by using a level to measure the flange for accuracy. If it is not level, adjust the flange using whichever method is necessary.

You can either use a screwdriver to rotate the flange or install plastic shims or metal turning clips to bring it to the correct level. Once you have achieved the correct level, secure the flange to the floor and attach the toilet.

How should a toilet flange be installed?

A toilet flange should be installed properly to ensure the stability and function of the toilet. The first step is to choose the right flange and make sure the flange fits the toilet and the existing drainpipe.

Make sure the flange is centered on the drainpipe, then mark the bolt holes with a pencil or marker. Secure the flange to the floor with lag bolts, then cut or trim the wax ring to the exact size needed for the flange.

Place the wax ring firmly around the flange and insert the toilet onto the flange. Finally, secure the toilet to the flange with the provided bolts and washers. The ends of the bolts should be flush with the floor and the washers should be tightened as much as possible.

Once everything is secure, the water supply should be connected to the toilet and the toilet should be tested to ensure proper flushing.

Does a toilet flange go inside or outside the drain pipe?

A toilet flange typically sits outside of the drain pipe. This is because it connects to the bottom of the toilet and not to the inside of the drain pipe itself. The flange creates an airtight seal with the toilet itself, and the drain pipe typically connects to the other side of the flange.

If the flange is too deep or too close to the drain pipe, the seal may not be as effective. To ensure a successful installation and a proper seal, the toilet flange should be installed outside of the drain pipe, and not within it.