Skip to Content

How do you tighten a toilet seat with conceal fittings?

To tighten a toilet seat with conceal fittings, start by removing the plastic caps that are located around the hinge bolts. You should then be able to see a threaded post inside the hinge. Using a wrench or pliers, tighten the post to a firm but reasonable level of tension, taking care to not over-tighten and cause damage.

Once the tension is balanced, replace the plastic cap to finish the job. If the original caps are missing, replacements can be found at a local hardware store. Additionally, some conceal fitting toilet seats may require a special wrench or Allen key to adjust the tension, so make sure to get the necessary tool before proceeding.

Lastly, if the seat has been installed for a while, the hinges may have become brittle, in which case it’s best to replace the seat rather than try to repair it.

How do you tighten a concealed toilet bolt?

When tightening a concealed toilet bolt, the first thing to do is turn off the water supply and flush the toilet to empty it. Then, remove the toilet from its position by unscrewing the nut located underneath it.

After that, locate the concealed toilet bolth, as it will be connected to the floor flange with two closely placed nuts. Use a wrench to hold the nuts while you unscrew them, then hold the toilet bolt in place while you tighten the nuts.

Finally, return the toilet to its original position and turn on the water supply.

How do you change a toilet seat on an enclosed toilet?

Changing a toilet seat on an enclosed toilet requires several steps:

1. Disassemble the Toilet Seat – First, you will need to remove the old toilet seat. Depending on the connection mechanism, this may mean unscrewing the mounting nuts or unscrewing the bolts at the back of the toilet seat.

2. Install the New Toilet Seat – Next, you will need to slide the new seat onto the toilet bowl. Some toilet seats are designed with screws that connect to the bowl while others may snap into the existing bolts.

Once the new seat is secured, you can tighten the mounting screws or nuts.

3. Adjust the Toilet Seat – Once the toilet seat is installed, you should check that the seat is level and properly aligned with the toilet bowl. If it is not, you can adjust the screws or bolts to make sure that the seat is even.

4. Test the Toilet Seat – Make sure to test the new seat before using it to make sure that it is properly secured. If everything checks out, you can now use your newly installed toilet seat.

How do you remove a hidden plastic toilet seat?

Removing a hidden plastic toilet seat requires some patience, especially because it could be connected to the bowl by a number of different types of fasteners. Generally, plastic toilet seats are attached to the bowl with either two or four small plastic bolts or screws that are hidden behind small caps.

To remove the hidden plastic toilet seat, start by gently prying off the small caps with a flathead screwdriver. Once the screws or bolts are exposed, use a Phillips head screwdriver to remove them. When all of the screws or bolts have been removed, lift the seat off of the bowl and it should be fully disconnected.

Depending on the age and condition of the toilet, you may need to replace the mounting hardware to ensure a secure fit. If needed, installation of a new hidden plastic toilet seat is the reverse of the above instructions.

What are the different types of toilet seat fittings?

There are four main types of toilet seat fittings:

1. Standard Fittings – This is the most common type of toilet seat fitting and includes bolts and screws that either attach directly to the toilet bowl or nut and washers attached to the underside of the toilet seat.

This type of fitting is very basic and easy to install.

2. Quick Release Fittings – This type of fitting requires no tools to install as the seat simply clips on and off from the toilet bowl. Quick Release Fittings come in metal or plastic, with metal being more durable and usually more expensive.

3. Soft-Close Toilet Seat Fittings – These fittings are often integrated with the hinges and are designed to prevent the seat slamming shut. Fittings of this type generally feature metal or plastic mounts and washers that connect the seat to the toilet bowl.

4. Elongated Fittings – Elongated fittings are designed with longer bolts, which extend down to the base of the toilet bowl, providing additional stability to the fitting, as well as an improved aesthetic look.

Elongated fittings are ideal for larger toilet bowls and are available in metal or plastic.

How do I know what type of toilet seat I have?

To determine the type of toilet seat you have, you’ll need to remove the current seat from the toilet to get a better look. Once the seat is off, you’ll look directly at the bowl itself and identify any telltale signs that indicate the particular type of seat.

For instance, most seats will have either a round or elongated shape, while other traditional style seats may feature a beveled edge along the bowl. Some seats also feature additional hinge mechanisms on either side of the bowl.

If you’re still unsure which style of seat you have, take a close look at how it attaches to the toilet itself. Round seats will typically attach to the toilet bowl using two bolts underneath the seat, while oval and elongated seats may utilize either two bolts or a plastic clamp style attachment.

Additionally, if you have a slow-close or comfort-style seat, you may also notice plastic fixtures or bolts around the bowl.

Once you’ve established the type of seat you have, you can purchase the correct replacement seat moving forward.

Do all toilet seats have the same fittings?

No, not all toilet seats have the same fittings. Toilet seats can come in various sizes and shapes, as well as with different fitting styles. These components indicate which toilet seat fits which toilet bowl.

Different fitting styles include snap-on, bolt-on, snap-in, and metal bolt-on. Additionally, most toilet seats now come with adjustable bolt sizes, so it is important to measure the distance from the back of the bowl to the mounting hole prior to purchasing a seat.

Furthermore, some toilets require the use of metal bolts or screws for installation, which may require the use of specific mounting equipment. As a result, it is important to double-check the toilet seat’s fitting before purchasing, in order to ensure that you buy the correct piece that is compatible with your toilet.

Why do some toilet seats not connect?

Some toilet seats may not be connected due to a few potential reasons. For example, it could be due to poor installation, the wrong size toilet seat being purchased for the toilet, or wear and tear on the seat.

Improper installation may occur if the seat is not properly secured to the toilet with the appropriate amount of bolts or screws. The seat can become loose and separate if the nuts securing it are not properly tightened.

Additionally, if the wrong sized toilet seat is purchased, it can cause a gap between the seat and the toilet. Finally, wear and tear on the seat can cause the seat to loosen over time and result in the need for replacement.

Do new toilet seats come with bolts?

Yes, new toilet seats usually come with bolts. The bolts and the nut that attaches the seat to the bowl typically come with the toilet seat. Depending on the type of toilet you buy, the toilet seat might come with plastic or metal mounting bolts and screws to mount it to the bowl.

It is also standard to include five slots or “ears” and some toilet seats have angle or offset ears, or an oblong slot, so make sure that you know the type of toilet you have when purchasing a new seat.

Additionally, the new seat might include a mounting installation kit with a non-corrosive nut, washers, and even a universal plunger assembly.

Why wont the screws on my toilet seat tighten?

Most likely, the screws on the toilet seat are not tightening due to the plastic nuts being stripped inside of the toilet bowl. This stripping occurs due to age and/or repeated installation or removal of the toilet seat.

The plastic nuts become softened or “stripped” when the screws go into them over and over, which makes them unable to hold the screw securely into place. To fix this issue, you can either replace the plastic nut and screws, or use a longer screw with a metal wing nut.

If replacing the nuts, two large wing nuts that thread onto the bolts holding the seat to the bowl can also be used, however this will require drilling a couple of holes into the bowl itself. Both of these options should work to tighten the seat, but it’s best to make sure to use the appropriate mounting hardware so it will stay in place.

How do you fix a screw hole that won’t tighten?

If you have a screw hole in a wall or other material that won’t tighten, there are a few steps you can take to try to fix the issue. First, check to see if the hole is stripped or damaged. If so, you may need to repair the hole before you can tighten the screw.

Depending on the material, this will involve either filling the hole with an appropriate filler or product, or using smaller screws to attach the material. Additionally, you can use an oversized screw.

This is a screw that is slightly larger than the original, and it will bite into the material and allow you to securely tighten the screw. Another option is to use a threaded insert. This is a small piece of metal that has threads cut into it.

Insert the threaded insert into the hole and then screw the screw into it. These inserts are available in a variety of sizes and materials, so make sure to find the one most suitable for your material and screw size.

Finally, you can use a screw anchor. These are available in plastic and metal, and fit into a hole of the appropriate size. You insert the anchor, then screw it into place. Once the anchor is in place, you can use screws of the appropriate size to securely fasten the material.

Are all toilet seat fixings the same?

No, all toilet seat fixings are not the same. The type of fixing you require will depend on the shape and size of your toilet bowl, as well as the model of toilet you have installed. Toilet seats come in standard fixings, but there are also brackets, screws and hinges available for various models that may require specific types of fittings.

The material of the fixing is also important, as some are made of brass, stainless steel or even plastic. It is best to consult with a professional plumber if you are unsure which type of fixing you need, to ensure you choose one that is compatible with your toilet.

How do I stop my toilet seat from moving sideways?

The best way to prevent your toilet seat from moving sideways is to make sure it’s correctly installed. Firstly, check that all the fixtures and fittings are securely and correctly tightened to the toilet bowl.

Secondly, if your toilet seat has adjustable hinges, use the slots to adjust them until the toilet seat snugly fits the bowl. For added stability, you could also add a mounting bracket to secure the seat even further.

Finally, replace the seat with one that has a sturdier design, such as a solid wood or hard plastic, if these methods do not provide a sufficient solution.

How do I get my toilet to sit flat?

If your toilet is not sitting flat on the floor, the first thing you should do is make sure that the toilet is firmly secured to the flange and properly sealed. The flange is usually a metal or plastic piece located beneath the toilet and is connected to the waste pipe.

You may need to use a wrench or pliers to check that the bolts connecting the flange to the toilet are properly secured. If they come off easily, use a thread sealant to ensure they stay in place.

Once the flange is properly sealed and connected, use a level to check that the toilet is sitting evenly on the floor. If not, you will need to make some small adjustments to the toilet’s feet. Start by loosening the adjustment nuts located on the toilet’s feet.

Then, using a screwdriver, make small adjustments to each foot until the toilet is sitting level and flat on the floor. Once it is sitting level, secure the adjustment nuts tightly to ensure the toilet stays in place.

If your toilet is still not sitting flat on the floor after these adjustments, the flange may need to be repaired or replaced. In this case, you should call a plumber or contact your local hardware store for advice and assistance.

Should the toilet seat be up or down while pooping?

The topic of whether the toilet seat should be up or down while pooping is somewhat controversial. In general, the consensus is that the toilet seat should stay in the down position if you’re the only one using the bathroom.

This is to prevent germs, debris, and other contaminants from spreading around the bathroom.

On the other hand, if you’re sharing the bathroom with others, it’s more economical and polite to leave the toilet seat up after each use. That way, other people who are using the bathroom don’t have to bother with lifting the toilet seat and then putting it down again.

Some people also argue that leaving the toilet seat up is actually better for hygiene because any germs from the lid are less likely to spread, as the lid will be in contact with the toilet seat and not the floor.

Ultimately, the decision of whether the toilet seat should be up or down is personal preference and dependent upon who is using the bathroom. If you’re using it alone, it’s best to leave the toilet seat down to keep the toilet bowl clean; but if you’re sharing the bathroom, it’s more courteous to leave the toilet seat up.