Skip to Content

How much does a snake cost to unclog your toilet?

The cost of unclogging a toilet with a snake typically depends on the complexity of the clog, the type of snake used, and who is doing the work. For a simple clog, a homeowner can rent a snake, which typically costs about $50 for a 24-hour period.

Hiring a plumber to unclog the toilet with a snake usually costs between $95 and $250, depending on the extent of the problem and the plumber’s hourly rate. If the clog is caused by a deep obstruction, such as tree roots, the plumber may need to use special equipment or chemicals to clear it, which may increase the cost of the job.

Additionally, if the snake becomes stuck, then the plumber will need to take special measures to remove it, which could also increase the cost of the job.

How much does a plumber charge to run a snake?

The cost of a plumber to run a snake will depend on a few factors, such as where you live, the difficulty of the job and the experience of the plumber. On average, you can expect to pay between seventy to three hundred dollars for a plumber to run a plumber’s snake.

For example, if the job is time-consuming and requires extra time and tools, the plumber may charge more than the average rate. Additionally, if there are any additional costs such as parts and materials needed, the total cost can be higher.

It is best to get a quote from a plumber beforehand and ask any questions you may have to understand the full cost of the job.

Can I snake a toilet myself?

Yes, you can snake a toilet yourself if you have the right tools and know-how. The first step is to turn off the water supply to the toilet, then flush it to remove as much of the water as possible. Next, you’ll need to locate the clog and determine whether it is deeper in the pipes or close to the surface.

If the clog is close to the surface, you may be able to clear it using a plunger. For deeper clogs, you’ll need to use a snake or auger. Make sure that you check the instruction manual of your tool to ensure you are using it correctly.

Finally, once you’ve cleared the clog, turn the water back on, flush the toilet and verify that the clog is gone. If the clog persists, contact a professional.

Do snakes work to unclog toilets?

No, snakes are not typically used to unclog toilets. Snakes are not designed or intended to be used in this way, and they can actually cause more damage if they are not used properly. Plungers are generally the best tool to use when trying to unclog a toilet, as plungers are made specifically for this purpose.

If using a plunger does not work, other options to consider are using a hand auger, calling a plumber, or using a chemical drain cleaner.

What do I do if my toilet won’t unclog?

If your toilet won’t unclog, there are a few things you can do. First, you can call a plumber if you don’t know how to do it yourself, as attempting to unclog your toilet without the adequate knowledge and tools can make the problem worse.

If you are planning on doing it yourself, the best tool to have is a toilet auger or a plunger. If you have these tools available, you should start by inserting the auger into the hole at the bottom of the toilet and try to work your way through the obstruction.

If that doesn’t work, try plunging the toilet by sealing the plunger onto the hole at the base of the toilet and then pushing and pulling it in a steady rhythm until the obstruction is cleared. If either of these methods still don’t unclog your toilet, the obstruction is most likely too deep in the pipe.

At that point, it is best to call a professional.

What is to unclog a toilet?

Unclogging a toilet can be a messy and potentially smelly job, but is usually a necessary task that must be done. In order to unclog a toilet, you will need to put on some rubber gloves, as you will be physically manipulating the toilet’s plumbing to unclog the system.

Before you begin, try using a plunger to manually break up the clog and see if the water will clear out the clogged pipes. If the plunger does not work, you can try using the manual auger, or a toilet snake.

First, loosen the screw located on the auger’s handle, and then feed the auger into the toilet’s bowl. Move it around until you feel it has reached the clog. Afterward, turn the handle of the auger until the clog has been broken.

You can also use a chemical cleaner to unclog the toilet. These are specially formulated products that will help break down and wash away the clog. Once you have successfully unclogged the toilet, make sure to flush it and do a few more tests to make sure it is unclogged.

Finally, make sure to clean up any remaining mess and to properly dispose of the gloves that you were using.

How do plumbers unclog toilets?

Plumbers use a variety of techniques to unclog toilets. First, they turn off the water supply to the toilet tank and flush the toilet to empty it. Then, using a plunger, the plumber will make several thrusting motions in an effort to dislodge whatever is causing the blockage.

If the plunger doesn’t work, the plumber may seek to remove the obstruction with an auger, or snake. The snake is fitted with a corkscrew-shaped piece of wire that is inserted into the drain pipe and turned to catch whatever is clogging the toilet and remove it.

If that does not work, the plumber may need to remove the toilet in order to access the extent of the blockage and unclog the drain pipe. In some cases, the plumber may have to cut into walls or floors in order to access the pipe.

After the obstruction is removed and the pipe is cleared, the plumber will ultimately reinstall the toilet.

Why put dish soap in toilet overnight?

Putting dish soap in your toilet overnight is a home remedy for unclogging a clogged toilet. This is because the dish soap acts as a lubricant and can help to break down any tough clogs in the pipes.

Additionally, adding a few drops of dish soap to the water can give the clog more buoyancy, allowing it to move through the system with more ease. Typically, it may take a few hours for the dish soap to completely dissolve the clog, but it is generally considered a safe, effective way to unclog toilets.

How do you manually snake a toilet?

Manually snaking a toilet is a relatively straightforward process as long as you have the right material and practice safe plumbing techniques. To start, you’ll need a closet auger, which is a flexible, coiled wire with a handle at the end.

It is important to ensure that the supply of water to the toilet is turned off before you begin.

Start by putting a bucket under the toilet’s drain and remove the toilet cap. Insert the closet auger into the drain hole, pushing it down as far as it will go until it reaches the clog. Then, slowly turn the auger’s handle clockwise in order to force the clog to break up.

You may need to occasionally pull the auger back up in order to remove the pieces of the clog.

Once the clog has been removed, you can use the auger to clean the sides of the pipe. Then, remove the auger and put the toilet cap back in place. Turn on the water supply and flush the toilet to check for any remnants of the clog or any backup.

If there are any problems, you’ll need to repeat the process until the clog is fully removed. After the clog is gone, you can use a plunger to ensure the pipe is completely free of any blockages.

How do you snake a toilet without an auger?

Snaking a toilet without an auger can be difficult, but it can be done. The first thing you need to do is gather the materials that you’ll need. You’ll need a wire, a flashlight, rubber gloves, and a bucket.

Begin by removing the water from the toilet bowl by flushing, and then continuing to hold down the flush lever until all of the water is gone. Next, put on the rubber gloves and use the wire to pull out any debris blocking the water flow.

You can also use the flashlight to get a better view of the toilet bowl, and the wire to navigate any tight spaces.

After you have retrieved the blockage, use the wire to scrub around the inner surfaces of the toilet bowl to remove any additional dirt and grime. Then, use a plunger to help push out any remaining blockage.

The plunger will help to force out any clogged material that wasn’t able to be removed with the wire.

Finally, re-fill the toilet bowl with clean water and test it out by flushing. If all goes well the toilet should now be free of any obstruction. Snaking a toilet without an auger can be a tricky task, but with the right preparation and supplies it can be done.

Can you snake a pipe through the toilet?

Yes, it is possible to snake a pipe through a toilet. It is a common plumbing issue to have a clog in your bathroom pipes and one way of clearing the clog is to snake the pipe. A plumber or do-it-yourselfer would use a plumbing snake, which is essentially a long metal coil with a handle, to insert into a toilet in order to reach the clog.

It is important to be careful when snaking the pipe through the toilet as not to damage or clog the pipe further. After the pipe has been snaked, it is important to flush the toilet to ensure that the clog has been cleared and the toilet is functioning properly.

What size snake do you need for a toilet?

When it comes to adding a snake to a toilet, the size you need depends on the type of clog you are dealing with. A 25-foot snake should be good for a general clog and fits most toilets, but if it is a more serious obstruction such as a tree root, then you may need to purchase a larger snake, such as a 50-foot or 75-foot model.

It is important to inspect the obstruction carefully and make sure you know what type of snake is suitable. If the obstruction is too large for the tool you have, you will need to rent a larger one. Although it is possible to purchase a smaller snake and connect multiple pieces together, this is not always recommended due to the difficulty of keeping the pieces tightly connected.

Why won’t my toilet unclog with a snake?

It is possible that your toilet won’t unclog with a snake because there could be an issue with the pipe beyond your reach. The snake can only go so far and any issues with the line beyond that point may still cause the blockage.

If the snake can’t clear the line, then it is likely that the obstruction is too far in the line and it will require additional tools to remove it, such as a sewer auger or drain cleaning machine. Additionally, the snake may not be able to unclog if the clog is caused by something more substantial than a typical blockage such as tree roots or large chunks of rock.

If this is the case, it is likely that you will need to call a plumber to have the line professionally cleaned.

Can snaking a drain make it worse?

Yes, it is possible that snaking or augering a drain can make it worse. If the snake is inserted too aggressively, it can punch a hole in the pipe and cause further damage. Also, improper use of a snake can break off small pieces of debris that were once blocking the drain, making them harder to locate and remove.

It is important to ensure that the snake is used properly and that it is the correct size for the pipe before attempting to use it. Additionally, if the snake does not seem to be helping in unblocking the drain, it is recommended to contact a plumber instead.

A professional plumber can determine the cause of the blockage and suggest the best way to address the issue.

Does toilet snake work better than plunger?

The answer as to whether a toilet snake works better than a plunger depends on the type and severity of clog experienced. Plungers are great for quickly removing small clogs located near the opening of an outlet pipe or on the toilet bowl drain.

This is because a plunger will create suction and in turn, pull the clog up and out of the pipe. Toilet snakes, on the other hand, are better suited for larger and more difficult clogs located further away from the pipe or drain.

The advantage of a toilet snake is that it can reach deep inside the pipe and have the ability to break up and remove a larger clog as opposed to just pushing it further down the pipe like a plunger can do.

In this case, a toilet snake is definitely the most effective tool for removing tougher clogs. However, no matter which tool you choose, it is important to wear protective gloves when using any tool to unclog a toilet.