Installing a Lyons shower base is a relatively straightforward process, but it requires a few essential tools and some basic DIY knowledge in order to get the job done correctly. First, begin by measuring the rough opening of the shower area to make sure that the Lyons shower base will fit.
Once the measurements are taken, it’s time to get started.
1. Turn off the water supply for the shower and ensure the pipes have been drained.
2. Place the shower base in the shower area and mark the four corners as perfectly level.
3. Use a wet saw and cut two slots in each corner, allowing you to use plastic anchors to securely attach the Lyons shower base in place.
4. Using a screwdriver, secure the plastic anchors into the wet-cut slots with screws.
5. Lay down a layer of grout and sealant along the perimeter of the shower base before pressing the base firmly into place.
6. Once the base is in place, add caulk and sealant to ensure a water-tight seal.
7. Use a drill and screwdriver to attach a tile backer board to the walls of the shower area, using screws and the pre-drilled holes.
8. Once the backer board is in place, it’s time to install the tiles, beginning with a row of full-sized tiles along the base of the shower and continuing up the walls.
9. Once the tiles are in place, use grout and sealant to complete the installation.
10. Finally, connect the drain, turn the water supply back on, and enjoy your brand new Lyons shower base!
Do I need mortar under shower pan?
Whether or not mortar is required under a shower pan will depend on the type of shower pan you choose. For example, mortar is typically required for pre-cast or poured concrete shower pans, as the mortar helps to secure the pan in place, and the mortar acts as a sealant.
On the other hand, if you opt for a plastic or fiberglass shower pan, mortar is not usually necessary. Since these pans are typically thinner and lighter than concrete, they already come with their own sealants, usually made of silicone or another rubber-based material, and are not typically anchored in the same way as concrete.
Ultimately, it is best to follow the installation instructions for the type of shower pan you choose. For example, instructions for a concrete shower pan may specifically require mortar, whereas instructions for a plastic or fiberglass shower pan may not.
Ultimately, using the proper materials is key to ensuring the integrity of your shower pan, so always be sure to reference the installation instructions when determining the materials needed for your shower pan.
What do you put under a shower base?
When installing a shower base, typically the first step is to place a layer of crack isolation membrane on the subfloor. This membrane helps protect the shower from movement of the subfloor, which could cause the grout to crack over time.
Once the membrane has been laid, it is important to use mortar to secure the shower base to the subfloor. For added security, it is a good idea to use screws to secure the shower base in place. Finally, it is important to use a waterproof sealant around the edges of the shower base to prevent water damage.
How do you support the base of a bathtub?
To support the base of a bathtub, it is important to first make sure the floor beneath the tub is strong enough to hold the tub’s weight. If a reinforcing material such as plywood is necessary, it should be placed below the tub before installation to make sure the tub is evenly distributed when supported.
Once the floor is prepared, you will need to secure the bathtub to the floor using lag screws. Lag screws are metal screws with square or hexagon head drives that are threaded into a hole drilled in the tub’s base.
Each lag screw should be secured into a wall stud or joist in the floor below the bathtub for additional support. Once the lag screws are installed, you should use a rubber-washered nut to secure the screw heads and further secure the tub to the floor.
Finally, caulk should be applied to seal the perimeter of the tub and provide additional waterproofing.
How do you fill a gap between shower surround and drywall?
Filling the gap between a shower surround and drywall requires the following steps:
1. Gather all the necessary supplies – you will need a backer rod, silicone caulk and a caulking gun.
2. Take measurements of the length and width of the gap to determine the proper backer rod size necessary.
3. Cut a piece of backer rod to fit the gap and place it in the space between the shower surround and the drywall.
4. Take the caulking gun and run a continuous line of silicone caulk around the edge of the backer rod.
5. When finished, wipe any excess caulk with a damp cloth or paper towel.
6. Allow the caulk to dry completely before using the shower.
7. If the caulk starts to peel or crack, repeat the steps above to fill any additional gaps.
How do you install a bathtub step by step?
1. Turn off the water supply to the area that you’ll be installing the bathtub.
2. Educate yourself on the type of bathtub you’ve purchased, and all instructions that come with it. Look up any instructions specific to your model, as they will vary widely model to model.
3. Gather all the necessary tools and supplies (sanding block, drill, saw, masonry bit, plaster and putty knives, wall adhesive, caulk, plumber’s tape, etc.), required for the job.
4. Prepare the area where the bathtub will be installed by removing the existing wall covering, such as tiles, drywall, wood paneling, etc. , being sure to save any pieces that may need to be reused (like a window trim).
5. If you need to re-frame the area, make sure to use the appropriate materials (such as treated lumber or metal framing) that meet local building codes.
6. Place the base of the tub in the area and make any necessary adjustments to the fit of the tub by leveling it and ensuring it meets the correct slope and angle needed for it to drain correctly.
7. Apply a bead of caulk or grout along the perimeter of the area of the tub and the wall surface, using either a caulk gun or putty knife.
8. Secure the tub with wall anchors, screws, or bolts if necessary, following manufacturer’s instructions and local building codes.
9. Drill any holes needed for any faucet or drain lines, and connect necessary plumbing, following the directions that came with your shower or tub accessories.
10. Make sure all connections are securely sealed and replace any wall covering that was removed earlier.
11. Carefully turn the water supply back on and test for leaks.
12. Lastly, apply grout or caulk along the seams between the wall and the bathtub for a finished look.
How are free standing tubs attached to floor?
Free standing tubs are typically attached to the floor by feet or a base. Feet are often preferred on certain designs as they’re typically easy to install, maintain and provide an adequate amount of support for the tub.
To attach feet to the tub, screws are often threaded through the bottom of the tub to the feet, though other mechanisms like metal straps and rubber gaskets can be used.
For heavier tubs or designs which require a larger support surface, a base can be used. A base is often comprised of three or four wooden boards which are evenly spaced beneath the tub. Wood screws or lengthy nails can be used to attach the boards to each other, while also securing them to the floor.
Other types of mechanical fasteners may also be used.
No matter which option is chosen, its important to ensure that the floor is capable of supporting the weight of the tub. For added support when using a base, a layer of plywood can be laid down to provide extra strength.
It can also be helpful to install bracing or blocking beneath the tub in order to anchor the base or feet more securely to the floor. That way, any flexing or shifting in the floor won’t affect the attachment of the tub.
Around the tub, caulk can also be used to fill any remaining gaps, create a seal and provide added support.
Can you install a tub surround directly to studs?
Yes, you can install a tub surround directly to studs. Most bathtubs are designed to be supported along the walls by wooden or metal framing (studs). Before installing the tub surround, you should use a level and a stud finder to locate the studs, mark them off, and determine where you need to drill to attach the backing board.
Once you have measured and marked all the studs, you can begin connecting the backing board to the studs. You will need to use galvanized wood screws and/or masonry anchors to secure the backing board to the wall so it is not loose or moving.
Once the backing board is attached to the studs, you can then install the tub surround. For this step, you will usually use adhesive glue or caulk to attach the surround to the board and also to seal all corners and seams.
A waterproof sealant between the backing board and the bathtub will also help keep the water from seeping behind the surround keeping your surround in great condition.
Does a free standing tub sit on tile?
A free standing tub can indeed be installed on tile. It is important to make sure that the subfloor and tile under the tub are able to hold the weight of the tub and the water. Tile should be laid very carefully on the subfloor, leaving no holes or gaps that could compromise the integrity of the installation.
For additional support, it is a good idea to use a mortar bed underneath the tile and then attach the tub directly to it. Additionally, a stress crack membrane should be laid over the tile if the tub is being installed directly on tile.
Finally, it is very important to ensure that all the grout is fully sealed and sealed a second time after installation, in order to ensure a long-lasting, water-tight installation.
How do I stop my freestanding tub from moving?
One way to prevent your freestanding tub from moving around is to install rubber feet on the bottom of the tub. The feet should be securely attached to the tub and will prevent it from sliding on the ground.
You can also anchor the tub to the floor with an anchor bolt system. This involves drilling holes into the floor, inserting the bolts, and then attaching them to the underside of the tub. Additionally, you can also place a non-slip rug underneath the tub to stop it from sliding.
Make sure the rug or mat is secured to the floor so it won’t move around or detach from the floor. In addition, you can also place a non-skid pad on the floor underneath the tub to keep it from sliding.
This pad should have a strong grip that will adhere to the floor and keep the tub from shifting.
What do you do with a gap between tub and floor?
A gap between the tub and the floor can be an annoying and potentially dangerous eyesore. If the gap has been present for a while, it may need to be addressed before it becomes a slip hazard. Fortunately, there are a few simple steps that you can take to seal the gap and make it less of an issue.
First, make sure the area is clean and dry before attempting to fill the gap. This is especially important if the tub is constructed of wood or composite, as moisture can cause rot and other damage if trapped in the structure.
Next, use a flexible sealant, such as silicone caulk, to fill in the gap and seal it off from water, dirt, and other debris. Apply the sealant generously and wait for it to dry before using the tub.
If the gap is particularly wide or deep, you may want to use a combination of sealant and additional supports, such as a small piece of hardwood or metal, to bridge the gap. These can be secured in place with screws or nails before filling in with sealant.
Once the sealant has dried, you can use a patch of decorative tile, sheet vinyl, or linoleum to finish the job.
Filling in a gap between the tub and the floor is a relatively easy DIY job that can help you avoid a potentially dangerous issue. With just a few simple steps and the right materials, you can seal off the gap and make the area look neat and clean again.
Should there be drywall behind my bathtub?
Yes, there should be drywall behind your bathtub. Drywall behind bathtubs serves several purposes. Firstly, it helps protect the insulation in your walls. Secondly, drywall prevents moisture from getting into the walls and causing mold growth, which can be difficult and expensive to remove.
Finally, it creates a barrier between the tub, the wall and any electrical outlets, which reduces the risk of electrical shock. Properly installed, drywaller also helps make the bathroom look more finished.
If you are installing a new bathtub, you’ll want to make sure the drywall is installed prior to the tub and all seams are sealed with a moisture-resistant caulk. If you have an existing tub, you can still install a drywall backer behind it if you need extra protection from moisture.
Drywall is easy to work with and can be cut to the specific dimensions of your tub.
Does a bathtub go on top of subfloor?
Yes, a bathtub can go on top of subfloor. However, it’s important to note that the subfloor must be in good condition with no warping or splitting. Additionally, you should also check that the subfloor is even and level, as any kind of slope or dip could cause the bathtub to crack or even leak.
Before installing the bathtub, you should always make sure the subfloor is properly reinforced and supported by installing additional bracing or plywood beneath it. This will help the bathtub sit properly and sturdily on the subfloor, preventing it from cracking or shifting when in use.
Additionally, it’s important to use appropriate sealant to fill any gaps between the bathtub and subfloor to prevent water from seeping through.
Does a bathtub need support underneath?
Yes, it is essential to provide support underneath a bathtub in order to ensure it is properly secured and stable. Without adequate support, a bathtub can shift and cause considerable damage to both the tub itself and surrounding areas.
Including attaching it to the wall and floor with a steel frame, bolting directly to the subfloor/joist, or using mortar and cement to secure the bathtub in place. Of these methods, the strongest form of support is by bolting the tub directly to the joists/subfloor, as this will best protect it from shifting and deteriorating due to excessive weight or movement.
In addition, it is also important to use a rubber gasket or sealant between the bathtub and the wall in order to properly seal it and create a watertight fit that will prevent water from entering walls and floors.
All of these steps are integral in providing the necessary support for a bathtub and ensuring it is tightly secured and structurally sound.
Do you need a flange for a linear shower drain?
Yes, a flange is usually necessary for a linear shower drain. The flange of a linear shower drain facilitates the connection of the drain to the drain pipe, which ensures a secure, watertight fit. The flange is usually attached to the drain opening, allowing the drain to be securely connected to the drain pipe.
The flange also prevents the drain from being pulled out of the floor and prevents water from leaking around the drain. To ensure proper water containment, and to avoid any potential damage to the shower floor, the flange should always be securely affixed to the relevant drain components with appropriate sealants.