Moving a toilet can be quite expensive, depending on the amount of work involved. If you just need to reposition your existing toilet a few inches, then this can be done relatively cheaply by just a plumber or handyman.
However, if you are trying to move a toilet from one room to another, or even changing its location within the same room, then this can incur higher costs. This is because the new location could involve additional factors such as having to reposition the water pipes to get the necessary water supply and drainage and to fit a new flange to attach the toilet.
Additionally, if access to the space is limited, or any part of the work needs to be done behind walls or floors, then it is likely that builders, electricians and plumbers would be needed to complete the relayout correctly.
Therefore, the cost of moving a toilet can range from a few hundred to a few thousand dollars depending on the complexity of the project.
How much does it cost to move the location of a toilet?
The cost of moving the location of a toilet depends on several factors, such as the complexity of the job, the distance of the new location and the materials needed to complete the project. On average, the cost to move a toilet usually falls somewhere between $250 and $1,000, with the majority of the cost being labor-intensive.
The complexity of the job depends on the existing plumbing setup, the type of toilet and the new location. If the relocation is a simple move to a new area within the same location, the cost may be around $250 to $500 including materials and labor.
If the relocation is more complex and is located in a different area within the house, the cost will increase and can range from $500 to $1,000. The cost of materials needed to complete the project (such as valves, flexible hoses, additional piping etc.
) will be on top of the labor cost. If the relocation is difficult, the cost will increase due to the time and the extra materials needed to complete the job. Additionally, if the contractor needs to access hard to reach places and rip out existing drywall and/or concrete, this will add to the cost of the project.
Professional plumbers will be able to give you a better estimate of the cost after assessing the complexity of the job.
Do you need planning permission to move a toilet?
In most situations, you will need planning permission to move a toilet in your house. Depending on the extent of the work, and which type of toilet you are installing, you may need to apply for a Building Regulations application.
If you’re just changing the location of the existing toilet, in general you don’t need planning permission. However, it’s still recommended to check with your local planning authority first, as you may need it if, for example, the new location is more than a few metres away from its current position.
If you want to make major improvements to the building such as moving a toilet from the ground floor to the first floor, then you will need planning permission. This will ensure the proposal complies with regulations, and is suitable for the location.
If you are moving an existing toilet to an outdoor area such as a garden or terrace, then you will again need planning permission, as well as building regulation approval.
In almost all cases you will need to hire an experienced plumber to carry out this work and make sure it’s done safely and in line with current regulations.
How many inches can you move a toilet?
It depends on your plumbing system and the layout of the bathroom. Generally speaking, a toilet can be moved up to a maximum of 12 inches, but regulations may differ depending on your specific location.
Moving the toilet more than 12 inches involves additional considerations that include changing the main drain line and possibly carrying out other modifications to the rest of the plumbing system. It is important to note that every move should be done by a licensed and experienced plumber as incorrect installation or moving of the toilet can lead to significant problems with the plumbing system.
How do you relocate a toilet?
Relocating a toilet can be a tricky task and requires a good deal of plumbing knowledge. Here is a step-by-step guide on how to relocate a toilet:
1. Shut off the main water supply. This will ensure that any water seeping through the pipes is minimized and that nothing gets damaged during the relocation process.
2. Disconnect the water line from the old toilet. This will be the most complicated step because it involves separating the old supply line from the toilet. Make sure you’re careful when removing the supply line, as it is important that it is not damaged or cracked.
3. Remove the toilet from the floor by unscrewing the two bolts that hold it down.
4. Place the new toilet in the desired spot and attach the wax seal to the base of the toilet. This seal will prevent leaking and provide a watertight seal to the drain. Secure the toilet to the floor using the two bolts that were removed earlier.
5. Connect the water line to the new toilet. Make sure all the seals are tight and there are no leaks.
6. Turn on the main water supply to the toilet and check for any leaks one last time.
7. Turn on the toilet’s water supply and flush it to make sure everything is working properly.
For the more complicated steps you may want to consider calling a plumber to assist you in the process. Relocating a toilet may seem daunting but with the right knowledge and tools, it’s not too difficult to complete.
Is it a big deal to move a toilet location?
Whether or not it is a big deal to move a toilet location depends on a variety of different factors. For example, if the area you plan on relocating the toilet to is already home to another plumbing fixture, such as a sink or tub, it can be a more difficult and extensive process.
It may require an electrical panel to be moved, new piping or fittings to be installed, and possibly even moving a wall in some cases. If you don’t have existing plumbing fixtures in that area, however, it can be much simpler.
You will still need to install new plumbing runs for the toilet, but it should be relatively straightforward as long as you don’t have to move the waste stacks or any external walls. It’s also important to consider ventilation when relocating a toilet, as it needs to be properly vented to a common vent stack using a vent pipe.
On top of that, you will also need to make sure you get the right size and type of toilet for the space as well. In short, moving a toilet location is doable depending on the situation, but it can sometimes be a big deal and require a lot of work to make it happen.
Can you move toilet location in bathroom?
Yes, it is possible to move the toilet location in a bathroom. Depending on the design of the bathroom and the plumbing underneath, it may be relatively straightforward or it could be a more complex project if sewer lines or other plumbing components need to be relocated or rerouted.
If the space allows it, the existing toilet flange can be cut away and a new one can be installed in the new desired location. The rough-in size (distance from the wall to the finished floor) should be determined early in the planning and the new flange should be put into place before any covering materials are installed.
It’s also important to make sure that the correct size toilet is purchased to fit the exact rough-in size needed.
Whether the project is to be a DIY job or requires a professional, moving the toilet in a bathroom requires a lot of time, effort and planning. The plumbing, flooring and tiling that may be impacted by the relocation should all be carefully considered before beginning any work.
How do you move a toilet to a new location?
Moving a toilet to a new location is a fairly involved process and requires careful planning. The first step is to turn off the water supply to the current toilet, drain and remove the toilet, then disconnect the wax seal.
Then you should measure the distance between the current location and the new one, keeping in mind that the toilet needs to be located at least 12 inches from any wall, and 12 inches to the center of the flange.
Next, you need to plot out where each section of the supply line will run and measure the length of the water supply line. You’ll want to make sure the new supply line is long enough to reach the new location and also avoid any obstacles.
You’ll also need to buy any new parts or components that are needed, such as a new wax seal or flange.
Once you have all of your supplies, you can begin the actual installation. You will need to make sure the flange is level and the toilet is at the proper height, then use a clamp to hold the supply line in place under the tank.
Then attach the new supply lines and wax seal to the flange before setting the toilet on top and bolting it down. Finally, turn the water supply back on and check for any leaks.
Can you move a toilet to where a shower was?
Yes, it is certainly possible to move a toilet to where a shower was. This is a fairly straightforward process if the water supply and drainage have already been installed and there is sufficient space in the bathroom.
First, the existing shower should be removed and then any necessary plumbing adjustments should be made. This could involve connecting to existing pipes or running new pipes, depending on the location of the prior shower.
It is also recommended that a new shut-off valve be installed before the toilet, so that water to the toilet can be shut off in case of a clog or an emergency. After the plumbing has been adjusted and all parts are connected properly, it is time to install the toilet.
You will need the toilet bowl, tank, a wax ring, and mounting bolts. The toilet bowl should be placed over the opening and secured with the wax ring. The tank should then be secured to the toilet bowl and connected to the water supply and drainage.
Bolts should be tightened, a wax ring should be applied, and the bowl should be set into place. Lastly, the seat should be attached and the toilet is ready for use.
Can I switch toilet and sink locations?
Yes, it is possible to switch the locations of a toilet and sink. Depending on the existing plumbing configurations and the layout of your bathroom, it may be fairly straightforward to switch the locations of the toilet and sink, or it may require a bit more effort.
The most important factor to consider when switching a toilet and sink is that both pieces need to be connected to the plumbing lines, so if you plan to switch the locations it’s important to do a full assessment of the existing plumbing configuration and ensure the new design is feasible.
You may need to hire a plumber to help you with the process, depending on your level of experience.
Tools and supplies that may be necessary for the job include a new sink and mounting brackets, a toilet flange, a wax ring, a toilet, supply lines and slip nuts, a P-trap, caulk and sealant, new shut-off valves and adapters, Teflon tape and a hacksaw.
Before beginning, it’s important to turn off the existing water supply. After that, the existing fixtures can be removed, and the new supply lines, shut-off valves, and the P-trap should be installed before setting the new toilet and sink.
Finally, the finishing touches such as the wax ring and caulk should be applied.
Switching the locations of a toilet and sink can be a relatively straightforward project for those with some DIY experience, but for those who are less experienced or unsure, it may be beneficial to consult with a professional plumber.
How far can a toilet be from the main drain?
The general rule for the location of toilet drains in relation to the main sewer line is that the toilet is allowed to be a maximum of 15 feet away from the main sewer line. In some cases, the distance can be a little bit more, depending on the specs of the specific job.
If the toilet is going to be more than 15 feet away, then a different type of toilet or different sized toilet and a larger-diameter drain pipe will be needed in order to accommodate the longer distance.
If the distance between the main sewer line and the toilet is greater than 15 feet, it is recommended to consult an experienced plumber to guide you through the regulations and determine what is best for your specific situation.
Can you change location of toilet?
Yes, it is possible to change the location of a toilet. The process can be done with some basic plumbing tools and a bit of time and effort. First, you will need to disconnect the old toilet from the plumbing in the wall and remove it from the floor.
Next, you will need to lay down a new flooring surface to fit the new size of the toilet and remove any broken pieces from the old area. You will then need to measure the drain pipe and cut it to the new size needed.
After that, you will need to fit the new wax seal to the drain pipe and reattach the toilet to the floor. Finally, you will need to attach the plumbing in the wall and turn on the water supply to test it out.
Ultimately, the process of changing the location of a toilet is fairly straightforward and can be done with some basic plumbing tools and a bit of time and effort.
Does a new toilet need building regulations?
Yes, a new toilet typically needs to meet building regulations. Building regulations are set by both federal and local authorities and ensure that construction meets safety, health, and sustainability standards.
Any new permanent construction, like a new toilet, must meet these requirements. This includes making sure the dimensions of the toilet meet the dimensions specified by the regulations and that the construction materials are safe.
Additionally, you may have to have your project inspected and approved by a qualified building inspector in some areas so make sure to check what is required by your local authorities.
In which direction toilet should not be there?
Ideally, a toilet should not be built in any of the following directions:
1. South-East: Toilets built in the south-east direction are thought to hinder money flow and affect the financial processes of any building.
2. North-West (NW): It is considered inauspicious to have a toilet in this direction as it is the corner of water and air element and is said to bring negative energy to the house. The north-west should be reserved for a sacred space, like a temple or a puja room.
3. South-West (SW): The South-West direction is not good for any bathroom or toilet as it is seen to clash with the earth element and gives negative energy in abundance.
4. Centre or Middle of the House/Building: It is deemed inauspicious to keep a toilet in the center of the house as it may bring energy problems and can prove to be a bad omen.
5. Main entrance: The main entrance should not have a toilet near it as it creates a sense of uneasiness among the visitors and might cause an imbalance in the house.
Where should we face while bathing?
Generally, when taking a bath, it is best to face in the direction of the tap. This ensures that when you open the tap, the water falls directly on your body, providing the most uniform coverage. However, if the tap is directly behind you, it can be more comfortable to move slightly so that you are facing your body towards the side of the tub, but close enough so that the tap is still easily accessible.
Additionally, when showering in a stand-up shower or cubicle, it can be useful to face the direction of the showerhead, as this will make sure that the water is equally distributed. Ultimately, however, it can really come down to personal preference and comfort, so figure out which direction works best for you.