Skip to Content

What are the rough in dimensions for a tub drain?

The rough in dimensions for a tub drain will vary depending upon the type of drain you have. Generally speaking, the hole cut in the floor should measure between 5 1/2 to 6 inches in diameter. The hole should have a rough edge of between 1/8 and 1/4 of an inch on all sides.

The height of the drain outlet should be anywhere between 6 1/2 and 8 inches from the finished floor level. The bottom of the drain should be between 1 1/2 to 2 1/2 inches above the highest point of the subfloor.

Lastly, the distance between the bottom of the supply tube and the top of the drain should be at least 1 1/4 inches. These are the general rough in dimensions for a tub drain, but certain models may require specific measurements.

It is always best to consult the installation instructions to ensure accuracy.

What size PVC pipe for a bathtub drain?

The size of the PVC pipe for a bathtub drain depends on the size of the bathtub. Generally, the pipes used are either 1 1/2 inches or 2 inches in diameter. However, the flange (the part that attaches the pipe to the bathtub) should always be 2 inches in diameter.

When choosing the size of the PVC pipe, it is important to measure the inlet and outlet side of the bathtub to make sure that the pipe is the appropriate size. Additionally, It is important to check if there are any local building codes that require a certain size PVC pipe.

These codes may vary based on where the bathtub is being installed. It is also important to note that many bathtubs will come with specific instructions for the type and size of PVC pipe to use. It is important to follow these instructions for both safety and functionality.

Can a bathtub have a 2 inch drain?

Yes, a bathtub can have a 2 inch drain. Most bathtubs are designed to accommodate drains with 2-inch downspouts. However, there are some bathtubs with larger or smaller drain sizes, such as 2-and-a-half-inch or even as small as 1-and-a-half inches in diameter.

Additionally, the drain size of a bathtub may be affected by the type of material. Many acrylic bathtubs come with a 2-inch drain, while some cast iron tubs may have a drain size of 2-and-a-half inches.

Overall, while 2-inch drains are common in bathtubs, it is important to double-check the size of the drain before making any purchases or installations.

Do you need a vent pipe for a tub drain?

Yes, a vent pipe is typically necessary for a tub drain. A vent pipe is essential for proper drainage, as it acts as an air intake area for the pipe system. This helps maintain the correct air pressure inside the waste pipe, and helps the water properly flow into the main drainage system.

Generally, the vent pipe should connect to the drain pipe, usually through the wall behind the tub, and then run up to the roof to the outside atmosphere. The size of the vent pipe should also be large enough to allow proper airflow, typically 1.

5 inches in diameter or larger. Additionally, the vent pipe should have a smooth inside wall with no debris blocking the airflow. It is important to check local codes to ensure that the rules and regulations regarding vent pipes are met.

Should I use plumbers putty or silicone on tub drain?

The decision of whether to use plumbers putty or silicone to seal a bathtub drain is one that should be based on type of drain assembly in the tub, and the application. Plumbers putty is a soft, malleable material that has been used to seal drains for many years.

It is ideal for use on a threaded drain pipe and is easy to install, but may not be very durable in wet areas such as a bathtub. Silicone is a more modern option, and it is extremely waterproof, so it is better suited to applications like bathtub drains that are frequently exposed to water.

When using silicone, it is important to make sure to use a product that is made specifically for bathroom fixtures, as other types of silicone may not be safe for contact with potable water.

What diameter should a tub drain be?

The diameter of a tub drain should be determined by the manufacturer’s instructions included with the purchase, as the proper diameter will depend on the type and size of the tub. Generally, tub drains range anywhere from 2-3 inches in diameter.

A 2 inch diameter is most common for residential installations, while 3 inch drains are often used for commercial installations and for tubs that are larger than 5 feet in length. Additionally, some tubs require a specific size drain, so you should always check the manufacturer’s instructions before selecting a drain size.

When selecting a drain pipe and fittings, it is important to make sure they are compatible with the material of your tub. Make sure the fitting is the same material as your tub and that the pipe is strong enough to support the weight of the tub and its contents.

How far can you run 2 inch drain pipe?

The length of run you can achieve with 2 inch drain pipe will depend on the type of pipe you are using and the building and plumbing codes in your area, as well as the terrain you’re working with. Generally, you can achieve a run of up to 25 feet with 2 inch drainage pipe in a straight line if you’re using rigid PVC.

If you’re using flexible or corrugated PVC, you may be able to achieve a longer run should you need it, depending on local plumbing codes. Different materials like clay, steel, and ABS may also be used to construct drainage pipes and will be affected differently by slope and terrain.

As such, the length of run achievable with different materials may also vary. Your best bet is to consult your local building codes or a professional plumber to determine how far your drainage pipe can effectively run.

Does a bathtub need a P trap?

Yes, a bathtub does need a P trap (which is also known as a drain trap). This is a type of plumbing fitting that is typically installed below a sink or bathtub and is designed to help prevent sewer gases from backing up into the house.

The P trap consists of a curved bit of drainpipe, with a fitting at either end that is connected to other pieces of the plumbing system, such as a sink drain, vent pipe, and sewer line. The P trap essentially forms a water seal in the drain by trapping some water in its bend, which prevents sewer gases from coming back into the house.

It is a required piece of bathroom plumbing and must be properly installed to ensure proper functioning.

Can you use 1 1 2 pipe for shower drain?

Yes, 1 1 2 pipe can be used for shower drain in select plumbing situations. Generally speaking, any type of pipe with a 1/2-inch diameter can be used for shower drainage. However, the 1 1/2-inch pipe size is usually recommended for shower drains since it has a greater capacity for water flow.

Additionally, it is important to consider bends in the pipe, since any sharp turns can decrease the drain capacity in a downward direction. When installing 1 1/2-inch pipes for shower drains, the pipes should be braided stainless steel to retain the strength of the pipe.

Additionally, galvanized elbows should be used instead of glued fittings whenever possible to avoid potential leaking or clogging.

Do shower drains need to be 2 inch?

The size of the shower drain will depend on the size of the shower, the drain location, the type of drain and any local codes or regulations. Generally, it is recommended to install shower drains with a minimum diameter of 2 inches.

In most cases, a standard shower drain will need to be 2 inch in diameter. In some cases, larger drains are needed if the shower has multiple showerheads or is a larger size than the standard, requiring more water to be drained.

Additionally, if the shower drain is located directly in the shower, it may require a larger diameter due to the amount of water it will be draining. It is important to check with local codes and regulations to ensure that the shower drain is installed properly.

What size are bathtub supply lines?

The size of bathtub piping supply lines typically depends on the type of material and pipe length. The most commonly used sizes are usually 1/2 inch for short runs and up to 3/4 or 1 inch for longer distances.

For plastic lines, 1/2-inch is usually the most popular size for showers, bath tubs and sinks that are located near each other. For metal lines, 3/4- or 1-inch is usually the preferred size.

The size of the supply tubing must match the size of the shut-off valves. This can be determined by noting the size of the shut-off valve ends. If the shut-off valve ends measure 3/8 inches, the supply tubing should be 3/8 inches in diameter.

Supply tubing and valves should be of the same diameter order to ensure proper water flow and to maintain pressure.

It is important to note that while these sizes are common, they are not set in stone. Always make sure to check the manufacturer’s requirements for the specific product being installed.

What is the minimum size drain line?

The minimum size for a drain line will depend on the size of the fixtures it serves, the number of fixtures connected, and the type of material used for the piping. Generally, for a home plumbing system, a 1-1/2″ drain line is the minimum size that should be used, although a 2″ drain line may be required for larger fixtures.

The most important factor when determining the minimum size for a drain line is the number of fixtures connected, as larger diameter piping will be needed for multiple fixtures. Using the correct diameter of pipe is important to ensure proper drainage and allow proper velocity of water through the pipes.

What should the rough opening be for a bathtub?

When installing a bathtub, the rough opening should typically be 5-1/2” greater than the finished opening of the bathtub itself. This additional space is necessary for the bathtub flange (lip) which will cover up the rough opening and create a water tight seal.

The rough opening should also be equal to or larger than the rough in dimensions specified by the bathtub manufacturer. The rough in dimension is the distance from the wall’s finished surface to the center of the drain.

Finally, the plumbing should be installed prior to framing the walls and bathtub rough-in to ensure it is level and in the correct spot when the tub is installed.

How much space do you need to install a bathtub?

When installing a bathtub, you will need to ensure that you have sufficient space for the tub to fit. Generally, the best way to measure for a bathtub is to measure the wall-to-wall distance of the space and add 6″ to 8″ of extra clearance for plumbing and installation.

In addition, you will also need to factor in an additional 20″ to 24″ of width or length to allow for movement within the room while using the tub. In most cases, a standard alcove bathtub needs a minimum area of 66″ long x 32″ wide with the access door overlapping the tub edges by at least 2″.

Clawfoot tubs and freestanding tubs require more space with a minimum area of 5ft long x 3ft to 4ft wide, depending on the size of the tub. Furthermore, ample space should be allowed around the tub for easy access and cleaning.

How to frame a bathtub alcove?

Framing a bathtub alcove is a relatively straightforward process.

1. Begin by taking measurements of the existing space and sketching out the size and shape of the alcove.

2. Once you have the measurements, cut 2x4s to the lengths needed to construct the frame. To make your job easier, use a miter saw to cut your pieces at the correct angles for easy assembly.

3. Assemble the frame together and secure the pieces together firmly with nails.

4. Add the top plate to the top of the frame to give it additional stability and rigidity.

5. Use drywall screws to attach ½ inch drywall to the frame. Use a straightedge to ensure the drywall sheets are perfectly aligned. Once the drywall is installed, use joint compound to fill and cover the seams between each panel.

6. Once the joint compound is completely dry, sand the joints smooth and caulk the edges.

7. Paint the drywall with an appropriate paint to finish the alcove.

By following these simple steps, you can easily create a beautiful alcove for your bathtub that will enhance your relaxing bath experience.