Skip to Content

What do I need to rough in a shower?

In order to rough in a shower, you will need a few essential tools and supplies. Firstly, you’ll need to make sure that the area you plan to install the shower has a proper water supply and drainage.

This will require some plumbing and piping to be installed, so you may need to call in a professional plumber to set this up for you.

Once that is complete, you’ll need to install the appropriate framing materials to construct the walls and floors of your shower. This may include studs, cement board, vapor barrier, and backer board.

It’s also important to ensure that the framing is properly sealed and waterproofed to prevent water damage in the future.

Next, you’ll need to install the shower pan. This piece will sit at the bottom of the shower to contain water and collect it as it drains away. When installing the shower pan, it’s important to make sure it is level and securely connected to the wall and floor framing.

Finally, you’ll need to install the tiles of your shower. This can be done either by laying down tiles yourself or hiring a professional tile installer. You’ll also need all of the appropriate materials for this, including grout, sealant, and waterproofing.

Once you’ve completed all of these steps, your shower should be successfully roughed in and ready for installation.

What are stops for in a shower rough in?

Stops are fittings used to control the water flow of a shower rough in. The stops allow for the shower head, tub spout, and diverter to be installed separately yet with precise water flow control. They are typically made of brass and consist of two metal cylinders that are threaded on either end, allowing them to be threaded onto the pipes connected to the wall studs.

The two cylinders form a stop as one is larger than the other, thus controlling the water flow. Depending on how far the larger part of the fitting is inserted into the wall, water can be completely shut off from the shower head, tub spout, and diverter.

Stops play an important role in the installation of a shower rough in as they provide precise control of the shut off valves and ensure that proper water flow is obtained.

How to build a frame for a shower?

Building the frame for a shower requires careful consideration and measuring, as a mistake here could impact the functionality of the shower and the stability of the parts overall. Here are the steps to consider when building a frame for a shower:

1. Measure the space: Measure the space or wall where you plan to install the shower frame. You’ll need to know the dimensions of the entire frame, including the height and width of the walls.

2. Cut 2×4’s: Cut the 2x4s to the desired length. Be sure to use a saw or miter box to ensure straight cuts.

3. Secure the furring strip: The furring strip should be the same length as your frame. Secure the furring strip to the wall and make sure the ends are flush.

4. Measure for stud placement: Measure for the stud placement and use a level to ensure that the studs are in a straight line and are level. Mark the studs on the furring strip.

5. Cut and place the studs: Cut the studs to the appropriate length and use a drill to mount them on the furring strip. Make sure that the studs are flush with the furring strip.

6. Secure the first piece of plywood: Once the studs are in place, cut a piece of plywood to the desired size. Secure it to the studs using screws or nails.

7. Attach the second piece of plywood: Cut the second piece of plywood to size and fit it between the studs. Secure it to the studs with screws or nails.

8. Seal the frame: Caulk any gaps between the frame and wall to make sure they’re waterproof.

9. Install the shower door: Measure the door opening and cut the necessary pieces to fit the size. Install them using screws or nails and seal them with caulk.

10. Install the shower head and piping: Measure the area for the shower head and piping and mark the location for each. Cut the necessary pieces to size and install them according to the manufacturer’s instructions.

Run a test to make sure that everything works correctly.

How high should shower rough in Be?

The ideal height for a shower rough in should be at least 82 inches from the finished floor, but may need to be adjusted depending on the type of fixtures used or the height of individual family members.

For example, if you’re using a taller shower head, or if you’re adjusting for a tall family member, you may need to make the rough in higher. The same is true if you’re installing a shower bench or seat.

It’s important to first analyze your fixtures and design before starting the rough-in so that you can determine the optimal height for your space. Once you’ve determined the ideal height, you’ll need to make specific measurements so that you can properly mark the locations of the studs, blocking, and other structural elements required for a successful shower rough in.

To ensure the best outcome, you should always consult a professional prior to beginning your project.

Can you plumb a shower with PEX?

Yes, you can plumb a shower with PEX. PEX, which stands for cross-linked polyethylene, is a type of flexible plastic pipe that is typically used in residential water lines and also in radiant heating systems.

PEX is an ideal choice for a shower because it can easily be bent around tight corners, making it much easier to route around obstacles such as joists or studs. Additionally, it can be connected with crimp rings, making it very fast and easy to install.

PEX pipe is also strong and durable, which means it can withstand high water pressure and temperature fluctuations. It is also a cost-effective option compared to copper or PVC pipe. If you are looking for an easy-to-install and cost-friendly material for your shower, then PEX is an excellent option.

Why is PEX not allowed?

PEX (plastic cross-linked polyethylene) piping is not allowed in many jurisdictions as it has not been officially approved as an acceptable material for interior plumbing systems. While PEX is often less expensive and easier to install than copper, and it resists corrosion, it can be less reliable over time.

PEX piping is prone to maintenance issues such as pinholes, corrosion, and deposits that can cause blockages, clogs, and reduced water pressure. Additionally, it has not been around long enough to be fully tested in the long-term and there is a lack of established standards for proper use, as well as concerns about the pumping capacity.

PEX has also been known to weaken over time due to sunlight and excessive temperature changes. Finally, PEX piping carries an increased risk of contamination because potential contaminants can leach out from inadequate manufacturing processes, improper installation, and aging materials.

For all of the above reasons, many jurisdictions do not allow PEX to be used for interior plumbing systems.

When should you not use PEX?

PEX (cross-linked polyethylene) is a very popular material for domestic and industrial use, but there are a few situations in which it should not be used, such as:

1. Direct exposure to UV rays: PEX cannot be exposed to direct UV rays, as this will reduce its lifespan and integrity.

2. Extreme temperatures: PEX has a maximum temperature resistance of 200°F, so water temperatures exceeding this should be avoided.

3. Highly acidic or basic chemicals: Certain chemicals like bleach or acidic cleaners can cause severe damage to PEX, so they should be avoided at all costs.

4. High pressure: PEX is not ideal for situations with high water pressure, such as water hammer.

5. Small pipe sizes: PEX is not recommended for pipe sizes lower than 0.5 inches, as it is unlikely to perform effectively in such applications.

In conclusion, while PEX is versatile and very durable in most applications, there are certain situations in which it should not be used, as outlined above.

What size PEX should I run to my shower?

The size of PEX piping you should use for your shower depends on several factors, such as the length of the run, the number of fixtures in the area, and the water pressure available. Generally speaking, a 1/2 inch PEX pipe is suitable for a shower and would provide an adequate flow for most applications.

However, for longer runs with multiple fixtures, you may need to use a 3/4 inch pipe to ensure an adequate flow of water. Additionally, if the water pressure available is unusually low, a larger diameter pipe may be necessary to ensure proper flow.

It is important to consult a qualified plumber to determine the appropriate size of pipe to use for your specific application.

Do professional plumbers use PEX?

Yes, professional plumbers often use PEX (cross-linked polyethylene) in their work. PEX has become widely popular in recent years due to its affordability, durability and versatility. It can easily be cut, bent, and maneuvered to fit any space.

It is corrosion-resistant and can be used with a variety of fittings, which makes it the ideal material for a wide range of plumbing applications. PEX is suitable for both hot and cold water lines, making it highly efficient for hot water systems.

It is also significantly less expensive than metal pipes and is even approved for use in most residential and commercial buildings. Professional plumbers also commonly use it as a base material for radiant floor heating systems.

Overall, PEX is an excellent and economical choice for a variety of plumbing projects.

Can PEX be used for steam shower?

Yes, PEX can be used for steam showers. PEX, also known as cross-linked polyethylene, is a reliable choice for steam shower applications due to its temperature and moisture tolerances, flexibility, and durability.

PEX provides a barrier to steam condensation, which can occur when other types of pipe are used in a steam shower. It also has superior resistance to aggressive chemicals and is fit for sealing threaded fittings.

PEX can also handle high temperature and pressure, making it perfect for steam showers. Additionally, it is usually a more affordable alternative to metal piping. Before installing PEX for a steam shower, it’s important to use the correct type of PEX pipe and to be aware of the local plumbing codes.

In some areas, a licensed plumber may be required to install the PEX pipes.

Should I run 3 4 PEX to the shower?

Whether you should run 3/4” PEX to the shower will depend on the size and requirements of your setup. Generally, 3/4″ PEX is not recommended for shower applications as it typically won’t be able to provide enough water pressure to a large shower head at a distance greater than 25-30 feet from the water heater, and could starve other fixtures in the home.

It is usually recommended to use 1” PEX for shower applications for this reason. However, if you are only running to a single shower head, have small water pressure requirements, and are located less than 25-30 feet from the water heater, then you could use 3/4” PEX without issue.

You should always consult a qualified professional to ensure your setup is up to code and will meet your needs safely.

Is it cheaper to run PEX or PVC?

The answer to this question depends on a number of factors, including the size and length of the pipes, the materials used, and the type of installation. Generally speaking, PEX, or cross-linked polyethylene, is the cheaper option between the two.

It is lightweight, flexible, and easier to install when compared to PVC, or Polyvinyl Chloride. PEX is less expensive to purchase, since PVC requires additional materials, such as PVC glue and sealants.

Additionally, PEX requires fewer fittings, further reducing overall costs.

PVC is a more durable material and is not affected by UV rays or extreme temperatures the way PEX is. Therefore, in the long run, PVC might be a better choice, since it has a much longer lifespan than PEX and is less prone to stretching or sagging over time.

Ultimately, the decision between PEX and PVC will depend on a variety of factors, and it is best to consult with a professional in order to make the most informed decision.

How many years does PEX pipe last?

PEX pipe is designed to last a long time and its lifespan can vary depending on the environment and how it is installed. Generally, it is estimated that PEX pipes can last anywhere from 25 to 50 years.

This timeline is contingent on the installation and effects of the surrounding environment, such as pH levels in nearby soil, exposure to chemicals, and changes in the local climate. Proper installation is also important to ensure a long lifespan for PEX pipes.

It is important to check connections, manifold connections, and fittings to make sure PEX pipe is securely in place, as well as check for any tiny signs of leaks or damage. Additionally, PEX has the ability to stand up to normal wear and tear very well and is more resistant to freezing than other pipes.

This means that, if treated properly, PEX pipe can last a long time.

What is better than PEX pipe?

When discussing alternatives to PEX pipe, one of the best options is CPVC (Chlorinated Polyvinyl Chloride) piping. CPVC is an excellent choice for residential and commercial plumbing applications due to its strength, durability and affordability.

It is also more resistant to corrosion and impact than PEX, making it more reliable over time. Additionally, CPVC piping is approved for both hot and cold water applications, as well as being approved for use in drinking water applications.

It is also more heat-resistant than PEX pipe and can handle temperatures up to 200°F, making it a great choice for areas with extreme temperatures. Lastly, CPVC is relatively easy to install, making it an ideal option for DIY projects.

Does a steam shower need a GFCI breaker?

Yes, a steam shower must have a GFCI breaker. A Ground Fault Circuit Interruptor (GFCI) breaker helps protect people from electrocution in the bathroom by detecting when an appliance or device has suddenly developed an imbalance in the amount of current flowing in a circuit.

When an imbalance is detected, the breaker instantly shutting off the power to the device. If a steam shower is being used in a bathroom, a GFCI breaker should be installed to ensure the safety of the people using it.

GFCI breakers are required by law in many areas and may be required by local hardware and electrical codes. Even if they are not required by law, they are still strongly recommended due to the potential dangers of steam showers without one.