Skip to Content

What kind of bathtub stopper do I have?

The type of bathtub stopper that you have depends on the make and model of your tub. Generally, bathtub stoppers come in three types: pop-up, plunger, or toe-tap. Pop-up stoppers are mounted on the top of the tub and are the most common type of stopper.

They are characterized by a visible stopper stem with a round knob at the top. When you pull the knob up, the stopper lifts, allowing the water to flow. Plunger stoppers are also mounted on top of the tub, but the stopper sits a few inches below the surface of the water.

It is operated when you press down the knob, which pushes the stopper up, blocking the water from flowing. Toe-tap stoppers are located on the side of the tub and are operated by pressing your foot against a lever at the side of the tub.

This lifts the stoppers out of the way and allows the water to flow. The type of stopper you have can be determined by visually inspecting the bathtub drain and checking for one of the stoppers described above.

Are all tub stoppers the same?

No, not all tub stoppers are the same. Depending on the type of bathroom sink drain you have, the type of stopper you need will vary. There are typically three types of tub stoppers: pop-up stoppers, lift-and-turn stoppers, and toe-touch stoppers.

Pop-up stoppers work with a lift rod and flange that attaches to the bottom of the sink. A lift-and-turn stopper is held in place with two screws and a rubber seal, while a toe-touch stopper is activated by pushing a button at the drain’s base.

Each type of stopper is designed to work in a different way, so it’s important to identify the right type of stopper for your bathroom sink before making a purchase. Additionally, be sure to measure the tub drain size to ensure that the stopper you buy fits correctly.

Are bathtub drain stoppers universal?

No, bathtub drain stoppers are not universal. Different types of bathtub drains require different stoppers. Including lift and turn stoppers, flip stoppers, push and pull stoppers, and toe-touch stoppers.

Knowing which type of drain stopper your bathtub requires is the key to making sure you purchase the correct one. Most stoppers can be replaced and it’s usually an easy DIY project. Before selecting a replacement, though, you should remove the old stopper to determine the type.

Additionally, you’ll need to measure the area around the bathtub’s drain to make sure the new stopper is the right size.

Are there different types of bathtub drains?

Yes, there are different types of bathtub drains. The most common type is a toe-touch or trip lever drain, which is operated by pressing a lever with your toe. There are also lift-and-turn drains, which are opened and closed by turning a knob in the center of the drain.

Push-pull stopper drains are operated by pushing and pulling a knob located on the overflow plate. Finally, plunger-type drains are opened and closed by pushing a knob located on the overflow plate and pulling up on the center of the stopper.

What is the stopper in the tub called?

The stopper in the tub is typically called a bathtub drain stopper. It is designed to stop the flow of water in a bathtub, preventing it from escaping when the tub is not in use. The stopper itself is usually a circular or oval rubber disc that fits over the tub drain and seals the basin so that water can be held in the tub without leaking.

The most common type of stopper is attached to a metal lever or handle on the outside of the tub, usually the side or standing facing the room. The handle allows the user to easily open and close the stopper by reversing the lever.

Other types of stoppers are installed from the underside of the tub, connected to a small rod or cable that operates the stopper from the bottom side. These types of stoppers often have adjustable or removable disks to control the flow of water and to allow for a more secure seal.

Can a tub stopper be replaced?

Yes, a tub stopper can be replaced. Although the exact process may vary depending on the type of stopper you have, in general, the process is fairly simple. First, you will need to remove the existing stopper by unscrewing it from the drain pipe.

Once the stopper is out, you can inspect the size and type of stopper to determine the correct replacement. Most stores that sell plumbing supplies or hardware will have a wide selection of tub stoppers in various sizes and shapes.

Once you have the new stopper, you will need to attach it by screwing it into the drain pipe and making sure it is properly sealed. This should fix any issues that you are having with the existing stopper.

How do you replace a bathtub drain stopper?

Replacing a bathtub drain stopper is an easy job and requires only a few tools. The first step is to remove the old drain stopper. Depending on the type of stopper you have, this can either be done by unscrewing it from the bottom, or cutting it away with a knife or utility knife.

Once the stopper is removed, use a brush and some vinegar-based cleaning solution to clean the strainer, the drain opening, and the threaded area where the new stopper will be installed.

Next, you’ll need to install the new drain stopper. Depending on your new stopper, there should be two or three pieces included with it. If there are three pieces, you will likely need to use a drain key or Allen wrench, which fits in the bottom of the drain, to tighten the screws.

Once the new stopper is installed, use pliers to tighten the nuts located at the top of the drain, ensuring that the stopper is snug and in place.

Now that the new stopper is in place, it’s time to turn the water back on and check to see if the stopper fits. If the stopper is too tight or too loose, simply adjust the nuts at the top of the drain until it fits properly.

Once the stopper is in the correct position, give it a few test lifts to ensure that it opens and closes properly.

With a few simple steps, you can replace a bathtub drain stopper by yourself. Remember to always turn off the water before attempting any plumbing repairs and make sure to refer to the instructions provided with your new stopper for the best results.

What size is a standard tub stopper?

A standard tub stopper typically measures between 2 and 3 inches in diameter, though sizes may vary depending on the make and model. Older models of tub stopper may be smaller, while some newer models may be larger.

Generally, the stopper should fit flush or nearly flush with the drain hole in the bottom of the tub. The hole typically measures around 1 7/8 inches in diameter, so it is important to match the size of the stopper to the size of the hole.

Some sizes may not fit at all, so be sure to measure carefully when ordering a new tub stopper.

Are there different size drain stoppers?

Yes, there are different size drain stoppers. The size of the drain stopper will depend on the size of the drain pipe it will be installed in. Some of the more common drain stopper sizes are 1 1/4″, 1 1/2″, 2″, and 3″.

The 1 1/4″ and 1 1/2″ drain stoppers are typically used for sinks, while the 2″ and 3″ sizes are more commonly used for bathtubs and showers. When choosing a drain stopper, it is important to make sure the stopper size matches the size of the drain pipe.

If the stopper is too large, it will not fit properly, while if it is too small, it will not be able to seal the drain tightly, which would allow water to escape.

What is a bathtub drum trap?

A bathtub drum trap is a plumbing trap that is commonly found under a bathtub or sink. It is usually made of metal and has a removable cover plate. The drum trap is designed to collect solid particles that may be in the water, such as hair and soap, before they have the chance to clog the entire plumbing system.

It also acts as a barrier against sewer gas odors and helps prevent flooding. The drum trap collects all the unwanted particles in its chamber, so they can easily be removed and disposed of. It is important to clean the trap regularly, as a build-up of debris can lead to blockages or even actively leaking soapy water, creating a messy and hazardous situation.

Drum traps are also known as S-traps, P-traps, and O-traps, depending on the shape of the bend in the pipe.

Are all bath plugs standard size?

No, all bath plugs are not standard size as there are several different sizes available on the market. Generally, bath plugs range from 2” to 4” in diameter, and the plug hole should correspond with the size of the plug.

The type of sink or bath tub used makes a difference when choosing a plug. If you are purchasing a new bath or sink, it is wise to check the size of the plug hole to ensure a matching plug can be found.

Some standard sized bath plugs have stoppers on the bottom, while others have a chain. If a plug is too large or too small, it will not properly fit the plug hole and will not be able to effectively stop the water flow.

How much does it cost to replace a stopper in the bathtub?

The cost to replace a bathtub stopper depends on several factors, such as the type of stopper and whether any plumbing services are required. Generally, replacing a stopper will cost between $20-$50 for a basic plastic or metal stopper, plus the cost of any additional materials needed, such as silicone or an adjustable lift rod.

If the project requires plumbing or carpentry services, the total cost can increase significantly. The best way to get an accurate cost estimate is to contact a local plumber or handyman for a quote.

How much does a plumber charge to replace a bathtub faucet?

The cost of a plumber to replace a bathtub faucet will depend on a variety of factors, including the type of faucet being replaced, the scope of the work, and the level of expertise of the plumber hired.

Generally, a plumber’s cost for replacing a bathtub faucet will range anywhere from $120 to $700, depending on these variables. The cost of the faucet itself will also play a factor in the overall cost of the job.

Some plumbers also offer a flat fee, wherein a pre-determined fee is paid up front regardless of how long the work takes. It is recommended to get a few estimates from different plumbers to determine which option is the best for the job.

Can you replace pop up bath plug with a normal plug?

Yes, it is possible to replace a pop-up bath plug with a normal plug. The process will depend on the manufacturer of your bath and the size of the drain hole. Generally, the process is quite straightforward and involves replacing the pop-up part of the plug mechanism with a basic plug and securing it in place with two locknuts.

Firstly, you will need to unscrew the pop-up plug from the top of the sink or bathtub and remove the drain cover. Then, you will need to measure the size of the drain hole and pick up the appropriate size of plug and two locknuts that will match it.

Finally, you must install the plug and locknuts onto the drain hole, making sure the plug is secure and leak-proof before replacing the drain cover and testing the results.

How do I know what size pop up drain I need?

When determining the size of pop up drain you need, first consider the sink for which the drain is intended. The drain size should match the measurement of the standard drain hole installed in the sink.

Many sinks will have a standard 3 1/2 inch drain hole, but some higher end sinks could have a larger 4 inch drain hole. Once you have determined the size of drain hole for the sink, you can purchase a pop up drain that matches the proper size.

Pop up drains often come in a variety of sizes from 1 1/2 inches to 4 inches. The size you need will depend on the size of the drain hole already installed in your sink. Specific drains are also manufactured to fit nonstandard sink drain holes, such as those found in vessel or corner sinks.

If you are purchasing a vessel sink, many manufacturers will provide what size pop up drain you need in the product specifications.

It is important to remember that pop up drains can also come in different lengths depending on the estimated height the drain is located above the trap. Depending on the sink installation, the drain tube may need to be extended in order to fit its connecting parts.

If so, make sure to measure the additional length needed before you purchase a pop up drain.